Question is ⇒ By the use of which of the following the PPM can be converted to PWM?, Options are ⇒ (A) A stable multivibrator, (B) Integrator, (C) Monostable multivibrator, (D) Bistable Multivibrator, (E) , Leave your comments or Download question paper.

Question is ⇒ By the use of which of the following the PPM can be converted to PWM?, Options are ⇒ (A) A stable multivibrator, (B) Integrator, (C) Monostable multivibrator, (D) Bistable Multivibrator, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	By the use of which of the following the PPM can be converted to PWM?
A.	A stable multivibrator [Wrong Answer]
B.	Integrator [Wrong Answer]
C.	Monostable multivibrator [Wrong Answer]
D.	Bistable Multivibrator [Correct Answer]
View Answer 2 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ T.V. broadcasting based on
line of sight communication
ionospheric propagation
ground wave
medium wave

⇒ An electric charge Q is placed in a dielectric medium which of the following quantities are independent of the dielectric constant ε of the medium
electric potential V and electric field intensity E
displacement density D and displacement φ
electric field intensity E and displacement φ
electric potential V and displacement φ

⇒ For a Gaussian process, auto-correlation also implies
statistical dependence
statistical independence
ergodic process
none of the above

⇒ Which of the following devices is a 'hot-electron' diode?
Thermionic tube diode
Schottky-Barrier diode
Thomson-Deletion diode
Thermal electron diode

⇒ When determining Thevenin's resistance of a circuit
all sources must be open circuited
all sources must be short circuited
all voltages sources must be open circuited and all current sources must be short circuited
all sources must be replaced by their internal resistances

⇒ Overall efficiency of class B amplifier is
0.72
0.75
0.785
0.7

⇒

Match the following:

	List I		List II
A.	Flash converter ADC	1.	requires conversion time of a few μs
B.	Dual slope ADC	2.	requires DAC
C.	Successive approximation ADC	3.	minimizes the effect of power supply interference
		4.	requires complex hardware
		5.	is a tracking ADC

A-2, B-3, C-4
A-4, B-3, C-2
A-5, B-4, C-3
A-1, B-2, C-5

⇒ The code which provides for parity check is
Baudot
ASCII
EBCDIC
Excess-3

⇒ In a series RC circuit Z = (R² + ω²C²)^0.5.
TRUE
FALSE

⇒ A current wave is i = 100e^-60t The initial and final values of current are
100 and 50
100 and 0
0 and 100
100 and 100

⇒ The current through a resistance R is shown in figure. The computed value of power
400 ± 0.42 W
400 ± 4.6 W
400 ± 8.85 W
400 ± 10.65 W

⇒ If a signal band limited for f_m is sampled at a rate less than 2 f_m the reconstructed signal will be
smaller in amplitude
distorted
having higher frequencies suppressed
none of the above

⇒

Match the following:

	List I (Set operation)		List II (Set operator)
A.	Set equality	1.	-
B.	Set inclusion	2.	=
C.	Set intersection	3.	< =
D.	Set difference	4.	∗

A-2, B-3, C-4, D-1
A-3, B-2, C-4, D-1
A-1, B-2, C-3, D-4
A-4, B-2, C-3, D-1

⇒ For maximum unclipped output from a CE amplifier, the Q point should be
at the centre of dc load line
at the centre of ac load line
at the centre of collector current
none of the above

⇒ Bandwidth will be
a.b
a + b
a
b

⇒ Television signals are propagated as ground waves.
TRUE
FALSE

⇒ Two identical hybrid tees are joined as shown in the given figure. If 16 mW power is fed into port 1, the power output at ports 2 , 3, 1', 2', 3' respectivel
8, 4, 2, 2, 0 mW
0, 8, 4, 4, 0 mW
0, 8, 2, 2, mW
8, 2, 4, 2, 0 mW

⇒ A network is causal if impulse response is zero for t < 0.
TRUE
FALSE

⇒ Which one condition is true to check the periodically for discrete time signal (where K is any integer, N is period, f₀ is frequency of signal)
f₀ = K/N
f₀ = K + N
f₀ = KN
f₀ = N/K

⇒ Consider the following tasks in a micro computer

Receiving data and instruction
Performing arithmetic computation
Performing logical computations
Storing data and instructions

Which of the above are performed by ALU?
2 only
2 and 3 only
1, 2 and 3 only
All

⇒ Hall coefficient is reciprocal of charge density.
TRUE
FALSE

⇒ Which of the following is used to generate PDM?
Free running multi-vibrator
Monostable multi-vibrator
JK flip-flop
Schmitt trigger

⇒ Strip lines are used at
microwave frequency
low frequency
High frequency
at any frequency

⇒ The element in the feedback circuit of a logarithmic amplifier using op-amp is
a resistor
a capacitor
an inductor
a diode

⇒ The interface chip for 8086 and 16 bit ADC is
8259
8255
8253
8251

⇒ Work function is the maximum energy required by the fastest electron at 0 K to escape from the metal surface.
TRUE
FALSE

⇒ In a JFET, the drain current is maximum when
V_GS = V_DS
V_GS = pinch off voltage
V_GS = 0
V_GS is negative

⇒ Polystyrene has a relative permittivity of 2.7. If the wave is incident at an angle θ_i of 30° from air into polystyrene, the angle of transmission will be nearly
0.2°
2°
18°
48°

⇒ Each of two cascaded stages has a voltage gain of 30. The overall gain is
3
9
30
900

⇒ While forming Routh's array, the situation of a row of zeros indicates that the system
has symmetrically located roots
is not sensitive to variations in gain
is stable
is unstable