Question is ⇒ The pure capacitor connected across an A.C. voltage consumed 20 W. This is due to, Options are ⇒ (A) the capacitive reactance in ohms, (B) the current flowing in the capacitor, (C) the fused capacitor was a big one, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ The pure capacitor connected across an A.C. voltage consumed 20 W. This is due to, Options are ⇒ (A) the capacitive reactance in ohms, (B) the current flowing in the capacitor, (C) the fused capacitor was a big one, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The pure capacitor connected across an A.C. voltage consumed 20 W. This is due to
A.	the capacitive reactance in ohms [Wrong Answer]
B.	the current flowing in the capacitor [Wrong Answer]
C.	the fused capacitor was a big one [Wrong Answer]
D.	none of the above [Correct Answer]
View Answer 2 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): The maximum efficiency of a class B push pull amplifier is 78.5%

Reason (R): A current mirror uses a compensating diode in parallel with the emitter diode

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ Which of the following does not cause losses in optical fibre cables?
Stepped index operation
Impurities
Microbending
Attenuation in glass

⇒ If the oscillator output is modulated by audio frequencies upto 10 kHz, the frequency range occupied by the side bands will be
711.9 kHz to 712.1 kHz
702 kHz to 722 kHz
692 kHz to 732 kHz
71.2 kHz to 71.20 kHz

⇒ The early effect in BJT is caused by
fast turn on
fast turn off
large collector base reverse bias
large emitter base forward bias

⇒ In the NMOS inverter
the driver and active load are enhancement type
driver is enhancement type and load depletion type
driver is depletion type and load enhancement type
both driver and load are depletion type

⇒ A 1000 kHz carrier is simultaneously modulated with 300 Hz, 800 Hz and 2 kHz audio sine waves. Which of the following frequency is least likely to be present in the output?
1002 kHz
1000 kHz
999.2 kHz
998.0 kHz

⇒ Which one of the following is true for EM wave propagation through rectangular waveguide of cross-section 2a x a
critical wavelength for TE₁₀ mode is the same as that for TE₀₂ mode
critical wavelength for TE₁₀ mode is one half of that for TE₁₀ mode
critical wavelength for TE₁₀ mode is the same as that for TM₁₀ mode
critical wavelength for TE₁₀ mode is double that for TE₀₁mode

⇒

Assertion (A): The circuit in figure produces repetitive narrow pulses when input is fed with sine or triangular waveform having peak value more than + V

Reason (R): The high gain op-amp produces voltages at two levels. If input is more than + V, the output is + 15 V otherwise the output is - 1
Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ The work done in moving a charge Q on an equipotential line for a distance d will be
V/d
QV/d
Q.d
zero

⇒ In which of the following schemes are several channels interleaved and transmitted together?
TDM
FDM
group
subgroup

⇒ A PIN diode can be used
as a shunt mounted switch
as a series mounted switch
both as series or shunt mounted switch
non of the above

⇒ The two conductors of a transmission line carry equal current I in opposite direction. The force on each conductor is
proportional to I
proportional to I²
proportional to distance between the lines
proportional to I³

⇒ In the given figure
A
B
A + B + C
ABC

⇒ Which of the following amplifier circuits has highest input impedance?
Circuit using BJT
Circuit using JFET
Circuit using MOSFET
Either (a) or (b)

⇒ Figure shows a NAND latch used as a switch debouncer. With the switch in STOP position. Q will be equal to
0
1
CLK
none of these

⇒ The radiation pattern of a parabola antenna is
omnidirectional
a figure of directional
highly directional
none of the above

⇒ In a JFET
gate source cut off voltage is equal to V_DS
gate source cut off voltage is equal to pinch off voltage
gate source cut off voltage is twice the pinch off voltage
gate source cut off voltage is equal to negative pinch off voltage

⇒ For broadside array, maxima will be obtain at
90°, 270°
180°
45°
at any angle

⇒ Find V_x V_y V_{zV_x = -6 V_y = 3 V_z = -3
V_x = -6 V_y = -3 V_z = 1
V_x = 6 V_y = 3 V_z = 3
V_x = 6 V_y = 1 V_z = 3}

⇒ A linear displacement digital transducer generally uses
straight binary code
BCD
gray code
hexadecimal code

⇒ In case of photo conductor for germanium when forbidden energy gap is 0.72 eV, the critical wavelength for intrinsic excitation will be
1.43 m
1.43 mm
1.73 mm
1.73 x 10¹² m

⇒ The most commonly used transistor amplifier circuit is
CB
CC
CE
CE or CC

⇒ In FM reception, amplitude disturbances due to static change
reduce the signal frequencies
increase the signal frequencies
disturb the signal frequencies
do not affect the signal frequencies

⇒ Fields are said to be circularly polarized if
their magnitudes are equal
their magnitudes are equal and they differ in phase by ± 90°
their magnitudes are unequal and they differ in phase ± 90°
their magnitudes are unequal and they are in phase

⇒ Electric shock is
always fatal
never fatal
sometimes fatal
always disfiguring

⇒ A step voltages is applied to RLC series circuit having R = 2 Ω, L = 1 H and C = 1 F. The transient current response will be
over damped
critically damped
under damped
any of the above depending the magnitude of voltage

⇒ When a ferromagnetic substance is magnetised, small changes in dimensions occur. Such a phenomenon is known as
magnetic hystresis
magnetic expansion
magneto striction
magneto calorisation

⇒ Performance of a PIN diode switch is represented by
insertion loss when switch is off
insertion loss when switch is on
insertion loss when switch is on and isolation loss when switch is off
insertion loss when switch is off and isolation loss when switch is on

⇒ A JK flip flop can be converted to D flip flop by
Connecting both J and K terminals to D
Connecting J terminal to D and leaving K open
Connecting K terminal to D and leaving J open
Connecting J terminal to D and K terminal to D through an inverter

⇒ If the current in a capacitor leads the voltage by 80°, the loss angle of capacitor is
80°
10°
100°
170°