Question is ⇒ System bus is the communication channel between microprocessor and peripherals., Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ System bus is the communication channel between microprocessor and peripherals., Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	System bus is the communication channel between microprocessor and peripherals.
A.	TRUE [Correct Answer]
B.	FALSE [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Find resistance R_B to bring transistor to threshold of saturation V_CB = 0, V_BE = 0.7 V, a =
1.5 kΩ
15 kΩ
10 kΩ
1 kΩ

⇒ The root locus branches
start from open loop poles and terminate at zeros
start from open loop zeros and terminate at poles
may start from pole or zero and terminate at another pole or zero
none of the above

⇒ Virus is a
computer hardware problem
an operating system
a computer program
a computer language

⇒ V_th = 0, if
there is no independent source in circuit
there is no dependent source in circuit
voltage source of infinite magnitude
none

⇒ In control systems the magnitude of error voltage
is very small
is very large
neither small nor large
may be any value from 0 to 50 V

⇒ The log magnitude curve for a constant gain K is a
horizontal straight line
horizontal straight line of magnitude 20 log K decibels
an inclined line having slope K
an inclined line having slope -K

⇒ The intermediate frequencies in VCR are
video 38.9 MHz and audio 33.4 MHz
38.9 MHz for both video and audio
33.4 MHz for both video and audio
33.4 MHz for video and 38.9 MHz for audio

⇒

Assertion (A): BCD code is used in pocket calculators

Reason (R): BCD code is slower than binary.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Light dependent resistors are
highly doped semiconductor
intrinsic semiconductor
lightly doped semiconductor
either (a) or (c)

⇒ In which n type device does p substrate extend upto silicon dioxide layer?
JFET
Depletion type MOSFET
Enhancement type MOSFET
Both (b) and (c)

⇒ The magnetic quantum number determines the component of angular momentum along a prescribed direction.
TRUE
FALSE

⇒ In an R-S latch, race condition occurs when
R is low and S is high
R and S are high
R and S are low
R is high and S is low

⇒ The velocity of electromagnetic wave in a good conductor is
3 x 10⁸ m/s
more than 3 x 10⁸ m/s
very low
high

⇒

Assertion (A): A common collector amplifier is used for matching a high impedance source to a low impedance load

Reason (R): A common collector amplifier has a near unity voltage gain

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ For the given truth table, the correct Boolean expressio
XYZ + X YZ + X Y Z
X Y Z + XYZ + X YZ
X Y Z + XYZ + XY Z
XYZ + XYZ + XY Z

⇒ The zener diode in the rectangular circuit shown in the figure has a zener voltage of 5.8 volts and a zener knee current of 0.5 mA. The maximum load current drawn from this circuit ensuring proper functioning over the input voltage range between 20 and 30 volts
23.7 mA
14.2 mA
13.7 mA
24.2 mA

⇒ A function table is required in very large numbers the memory most switched for this purpose would be
ROM
PROM
EPROM
EAROM

⇒ Cross-over distortion behaviour is a characteristic of
class A output stage
class B output stage
class AB output stage
common base output stage

⇒ In a practical voltage source, the terminal voltage
cannot be less than source voltage
cannot be higher than source voltage
is always less than source voltage
is always equal to source voltage

⇒ In a coupled coil the primary has 100 turns and secondary has 200 turns. The primary produces, a flux Φ = e^-t. The coefficient of coupling is 1. The voltages induced in secondary is
200 e^-t V
200 e^t V
200 V
none of the above

⇒ SSB can be generated by
filter method
phase cancellation method
good attenuation characteristics
all of the above

⇒ A high level language is less efficient than machine language.
TRUE
FALSE

⇒ In a power system, reactive power is necessary for
power transmission
stabilising the voltage level
counteracting the effect of reactance in the transmission system
none of the above

⇒ The units of transistor h parameters h₁₁ and h₂₂ are the same.
TRUE
FALSE

⇒ When a dc chopper feeds an RLE load, the load current, during steady state operation
remains constant
varies between maximum and minimum values
may remain constant or vary
is constant if R is constant

⇒ Non-coherently detection is not possible for
PSK
ASK
FSK
both (a) and (c)

⇒ Which of the following real variable names is not valid in Fortran?
BETA
ALPHA
A
AB * 2

⇒ As per time displacement theorem in Laplace transformation, displacement in the time domain by T becomes
division by s in the s domain
division by e^-sT in the s domain
multiplication by s in the s domain
multiplication by e^-sT in the s domain

⇒ A system has high gain and phase margin. The system is
very stable
sluggish
very stable and sluggish
oscillatory

⇒ In the circuit figure LED will be on when v_{1less than 6 V
more than 6 V
less than 12 V
more than 12 V}