Question is ⇒ Which of the following devices uses a slow wave structure?, Options are ⇒ (A) Klystron two cavity amplifier, (B) Klystron multicavity amplifier, (C) Reflex klystron oscillator, (D) TWT, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following devices uses a slow wave structure?, Options are ⇒ (A) Klystron two cavity amplifier, (B) Klystron multicavity amplifier, (C) Reflex klystron oscillator, (D) TWT, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following devices uses a slow wave structure?
A.	Klystron two cavity amplifier [Wrong Answer]
B.	Klystron multicavity amplifier [Wrong Answer]
C.	Reflex klystron oscillator [Wrong Answer]
D.	TWT [Correct Answer]
View Answer 1 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which quantity controls the effectiveness of LED in emitting light?
Applied voltage
Current
Extent of doping
Temperature

⇒ A single phase half wave rectifier is feeding a resistive load. When a = 0, dc output voltage is 127 V. When a = 30°, the dc output voltage will be about
127 V
120 V
110 V
100 V

⇒ The audio frequency range is
5 Hz to 1 kHz
50 Hz to 20 kHz
16 Hz to 20 kHz
0 Hz to 20 kHz

⇒ Figure shows the feedback network of one of the very popular types of sinusoidal oscillators. Which one is t
Weinbridge oscillator
Hartley oscillator
Colpitt's oscillator
R-C phase shift oscillator

⇒ In a transistor CE mode, V_CC = +30 V. If the transistor is in cut off region, V_CE =
+30 V
+20 V
10 V
zero

⇒ The service area of a TV transmitter is a little beyond radio horizon.
TRUE
FALSE

⇒ Consider the following; for a loss-less transmission line we can write,

Z_in = - jz₀ for a shorted line with l = λ/8
Z_in = ± j ∞ for a shorted line with l = λ/4
Z_in= jz₀ for an open line with l = λ/2
Z_in = 0 for a matched line of any length

Select the correct answer using the codes given below codes.
1, 2
2, 3
1, 3
2, 4

⇒ The bandwidth required for amplitude modulation is
half the frequency of modulating signal
equal to the frequency of modulating signal
twice the frequency of modulating signal
four times the frequency of modulating signal

⇒ In 8085, the pairing of registers B, C, D, E, H, L is
B - C, D - E, H - L
B - D, C - E, H - L
B - C, D - L, H - E
B - H, D - E, C - L

⇒ The K-map for a Boolean function is shown in figure. The number of essential prime implicants for this functio
4
5
6
8

⇒ In a circular waveguide with radius r, the dominant mode is
TM₀₁
TE₀₁
TM₁₁
TE₁₁

⇒

Assertion (A): If power gain doubles the power gain increases by 3 dB

Reason (R): The bel power gain of cascaded stages is equal to sum of each bel power gain

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ Consider the frequency modulated signal 10 cos (2p x 10⁵t + 5 sin (2p x 1500t) + 7.5 sin (2p x 1000t) with carrier frequency of 10⁵Hz. The modulation index is
12.5
10
7.5
5

⇒

Assertion (A): Microprocessor 8085 has 16 address bus lines and 8 data bus lines.

Reason (R): Address bus in 8085 is unidirectional.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ When a binary adder is used as BCD adder, the sum is
correct when it is < 9
correct when it is > 9
correct when it is < 16
none of these

⇒ The spectrum of the white noise and an impulse function is similar in following aspects
both have similar magnitude spectrum
both have similar magnitude and Phase spectrum
no relation
similar phase spectrum

⇒ Hysteresis loss in a transformer working at 220 V and at a frequency of 50 Hz is 100 W. When the transformer is operated at 220 V and at a frequency of 100 Hz, what is the hysteresis loss?
50 W
100 W
200 W
400 W

⇒

Assertion (A): When the anode current of an SCR starts increasing during turn on process, the anode cathode voltage drop starts decreasing.

Reason (R): During turn on the reverse biased junction in SCR breaksdown.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ In a cycloconverter it is possible to vary
only output frequency
only output voltage
both output voltage and frequency but not simultaneously
both output voltage and output frequency simultaneously

⇒ Which of the following statement regarding link loss for a satellite is wrong?
For fixed antenna, it is inversely proportional to f²
For fixed frequency, it is inversely proportional to the product of the antenna aperture areas
For a given satellite operating at a given frequency, it is inversely proportional to
Loss in down-link is negligible as compared to that in uplink

⇒

Assertion (A): A half cycle of sine wave can be expressed as sum of sine wave and another sine wave shifted by T/2 where T is the time period.

Reason (R): The function u(t - t₀) - u(t - t₀ - T) is a gate function occuring at t = t₀ and of duration T.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ No load d.c. output will be least in case of
half wave rectifier
full wave rectifier
bridge rectifier
three phase full wave rectifier

⇒ Heat in calories = I²Rt/4.186.
TRUE
FALSE

⇒ Microwaves are used for
telephony
radio broadcast
TV systems
all of the above

⇒ In an ac circuit, the maximum and minimum values of power factor can be
2 and 0
1 and 0
0 and -1
1 and -1

⇒ For a Gaussian process, auto-correlation also implies
statistical dependence
statistical independence
ergodic process
none of the above

⇒ The logic circuit of the given figure realizes the func
(A + B + C)(D)(E)
(A + B + C) (D)(E)
(A + B = C) (D)(E)
(A + B + C)(D)(E)

⇒ An op-amp uses
RC coupling
direct coupling
transformer coupling
either (b) or (c)

⇒ Power diodes are generally
silicon diodes
germanium diodes
either of the above
none of the above

⇒ The closing of switch S₁ and S₂ in figure will ligh
lamp L₁ only
lamps L₁ and L₂
none of them
lamp L₂ only