Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The peak value of a sine wave is 200 V. Its average value is |

A. | 127.4V [Correct Answer] |

B. | 141.4V [Wrong Answer] |

C. | 282.8V [Wrong Answer] |

D. | 200 V [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :Ravinder Saini Said on 2019-05-01 06:08:260.637*200=127.4 Virendra Said on 2016-11-09 02:04:11Vavg=Vpeak*0.637 Rahul Said on 2015-11-14 03:14:02.637*Imax Pallavi Said on 2015-08-24 07:32:16.637x200 !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ Which of the following circuit component opposes the change in the circuit voltage

Inductance

Capacitance

Conductance

Resistance

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?

0.5A

1.5 A

2A

3A

⇒ In a series resonant circuit, the impedance of the circuit is

Maximum

Minimum

Zero

Infinite

⇒ The power taken by a 3-Φ load is given by the expression

√3 V

_{L}I

_{L}sinΦ

√3 V

_{L}I

_{L}cosΦ

3 V

_{L}I

_{L}sinΦ

3 V

_{L}I

_{L}cosΦ

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in

Parallel

Series

Either (A) or (B)

None

⇒ Form factor for a sine wave is

1.414

0.707

1.11

0.637

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?

50V

82.8V

100V

173.2 V

⇒ The negative maximum of a cosine wave occurs at

30

45

90

180

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees

90

60

45

30

⇒ The unit of frequency of an A.C. signal is

Cycle

Cycle-sec

Hertz

Hertz/sec

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?

Square wave

Half wave rectified sine wave

Triangular wave

Sine wave

⇒ Which of the following is not a non-linear element ?

Transistor

Heater coil

Diode

Electric arc with unlike electrodes

⇒ Capacitors for power factor correction are rated in

kW

kVA

kV

kVAR

⇒ At half power points of a resonance curve, the current is____ times the maximum current.

1/2

1/ √2

√2

2

⇒ The dual of a loop is

Twig

Node pair

Mesh

Tree

⇒ For a sine wave with peak value E

_{max}the average value is

0.636 E

_{max}

0.707 E

_{max}

0.434 E

_{max}

1.414 E

_{max}

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.

Low

Very low

High

Very high

⇒ For the same peak value of voltage which wave form will have the least r.m.s. value ?

Sine wave

Square wave

Triangular wave

Full wave rectified sine wave

⇒ The form factor is the ratio of

Peak value to r.m.s. value

r.m.s. value to average value

Average value to r.m.s. value

None of these

⇒ The product of apparent power and cosine of the phase angle between circuit voltage and current is

True power

Reactive power

Volt-amperes

Instantaneous power

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is

70.7 A

141.4A

150A

282.8 A

⇒ Power factor of electric bulb is

Zero

Lagging

Leading

Unity

⇒ Power factor of the following circuit will be zero

Resistance

Inductance

Capacitance

Both (B) and (C)

⇒ In an A.C. circuit power is dissipated in

Resistance only

Inductance only

Capacitance only

None of the above

⇒ What inductance will give the same reactance as a capacitor of 2 µF when both are at 50 Hz?

5 H

10 H

15 H

20 H

⇒ The power is measured in terms of decibles in case of

Electronic equipment

Transformers

Current transformers

Auto-transformers

⇒ In a R-L-C series circuit if voltage V across the circuit is reduced to half the current I will change to

2 I

I/2

3/4 I

5/8 I

⇒ The r.m.s. value and mean value is the same in the case of

Triangular wave

Sine wave

Square wave

Half wave rectified sine wave

⇒ For a sine wave with peak value I

_{max}the r.m.s. value is

0.5 I

_{max}

0.707 I

_{max}

0.9 I

_{max}

1.414 I

_{max}

⇒ In A.C. circuit laminated iron is invariably used in order to

Reduce eddy current loss

Increase heat radiation

Make assembly cheap and easier

Reduce circuit permeability