Question is ⇒ Form factor for a sine wave is, Options are ⇒ (A) 1.414, (B) 0.707, (C) 1.11, (D) 0.637, (E) , Leave your comments or Download question paper.

Question is ⇒ Form factor for a sine wave is, Options are ⇒ (A) 1.414, (B) 0.707, (C) 1.11, (D) 0.637, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Form factor for a sine wave is
A.	1.414 [Wrong Answer]
B.	0.707 [Wrong Answer]
C.	1.11 [Correct Answer]
D.	0.637 [Wrong Answer]
View Answer 14 -7 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a pure resistive circuit
Current lags behind the voltage by 90°
Current leads the voltage by 90°
Current can lead or lag the voltage by 90°
Current is in phase with the voltage

⇒ A coil with large distributed capacitance has a
High resonant frequency
Low resonant frequency
Low quality factor
Low resistance

⇒ What inductance will give the same reactance as a capacitor of 2 µF when both are at 50 Hz?
5 H
10 H
15 H
20 H

⇒ Form factor is the ratio of
Average value/r.m.s. value
Average value/peak value
r.m.s. value/average value
r.m.s. value/peak value

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in
Parallel
Series
Either (A) or (B)
None

⇒ The power is measured in terms of decibles in case of
Electronic equipment
Transformers
Current transformers
Auto-transformers

⇒ The power taken by a 3-Φ load is given by the expression
√3 V_L I_L sinΦ
√3 V_L I_L cosΦ
3 V_L I_L sinΦ
3 V_L I_L cosΦ

⇒ The power factor of a series R-L-C circuit at its half-power points is
Unity
Lagging
Leading
Lagging or leading

⇒ The transient currents are associated with the
Changes in the stored energy in the inductors and capacitors
Impedance of the current
Applied voltage to the circuit
Resistance of the circuit

⇒ In A.C. circuit laminated iron is invariably used in order to
Reduce eddy current loss
Increase heat radiation
Make assembly cheap and easier
Reduce circuit permeability

⇒ Form factor for a sine wave is
1.414
0.707
1.11
0.637

⇒ The r.m.s. value of pure cosine function is
0.5 of peak value
0.707 of peak value
Same as peak value
Zero

⇒ For the full wave rectified sine wave the r.m.s. value is
0.707 I_max
0.636 I_max
0.318 I_max
Zero

⇒ Ohm is the unit of all of the following except
Inductive reactance
Capacitive reactance
Resistance
Capacitance

⇒ Which of the following statement is incorrect ?
Resistance is a passive element
Voltage source is an active element
Conductance is a passive element
Current source is a passive element

⇒ The value of operator j2 is equal to
Zero
+1
-1
√-1

⇒ Higher the Q of a series circuit
Broader its resonance curve
Narrower its pass band
Greater its band width
Sharper its resonace

⇒ Power factor of electric bulb is
Zero
Lagging
Leading
Unity

⇒ The voltage of domestic supply is 220 V. This figure represents-
Mean value
r.m.s. value
Peak value
Average value

⇒ Which of the following waves has the highest value of peak factor '?
Square wave
Sine wave
Half wave rectifier sine wave
Triangular wave

⇒ The form factor is the ratio of
Peak value to r.m.s. value
r.m.s. value to average value
Average value to r.m.s. value
None of these

⇒ For a sine wave with peak value I_max the r.m.s. value is
0.5 I_max
0.707 I_max
0.9 I_max
1.414 I_max

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.
Low
Very low
High
Very high

⇒ Capacitors for power factor correction are rated in
kW
kVA
kV
kVAR

⇒ The dual of a link is
Twig
Node
Loop
Tree branch

⇒ The negative maximum of a cosine wave occurs at
30
45
90
180

⇒ The series element of a band stop filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ In an A.C. circuit I sin Φ is called
Active component
Wattless component
Any of the above
None of these

⇒ The best place to install a capacitor is
Very near to inductive load
Across the terminals of the inductive load
Far away from the inductive load
Any where

⇒ While drawing vector diagram for a series circuit the reference vector is
Voltage
Current
Power
Phase angle