Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The r.m.s. value of a half-wave rectified current is 100 A. Its value for full-wave rectification would be____ amperes. |

A. | 141.4 [Correct Answer] |

B. | 200 [Wrong Answer] |

C. | 200/π [Wrong Answer] |

D. | 40/π [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :Abhijit Said on 2017-06-19 04:22:51plz explain the ans Virendra Said on 2016-11-09 02:28:04100/0.707 !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?

0.5A

1.5 A

2A

3A

⇒ Capacitive reactance is more when

Capacitances is less and frequency of supply is less

Capacitance is less and frequency of supply is more

Capacitance is more and frequency of supply is less

Capacitance is more and frequency of supply is more

⇒ Which of the following is not a non-linear element ?

Transistor

Heater coil

Diode

Electric arc with unlike electrodes

⇒ At very low frequencies a series R-C circuit behaves as almost purely____

Resistive

Inductive

Capacitive

None of these

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ A resonance curve for a series circuit is a plot of frequency versus

Current

Voltage

Impedance

Reactance

⇒ For a sine wave with peak value I

_{max}the r.m.s. value is

0.5 I

_{max}

0.707 I

_{max}

0.9 I

_{max}

1.414 I

_{max}

⇒ The power taken by a 3-Φ load is given by the expression

√3 V

_{L}I

_{L}sinΦ

√3 V

_{L}I

_{L}cosΦ

3 V

_{L}I

_{L}sinΦ

3 V

_{L}I

_{L}cosΦ

⇒ A network is said to be non-linear if it does not satisfy

Homogeneity condition

Superposition condition

Both (A) and (B)

Associative condition

⇒ The reflection co-efficient of the simplest standing wave is

+1

1

Zero

Infinity

⇒ The transient currents are associated with the

Changes in the stored energy in the inductors and capacitors

Impedance of the current

Applied voltage to the circuit

Resistance of the circuit

⇒ The power factor of incandescent bulb is

0.8 lagging

0.8 leading

Unity

Zero

⇒ Power factor of electric bulb is

Zero

Lagging

Leading

Unity

⇒ Inductance affects the direct current flow

Only at the time of turning off

Only at the time of turning on

At the time of turning on and off

At all the time of operation

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage

180°

90°

60°

0°

⇒ The power factor of a series R-L-C circuit at its half-power points is

Unity

Lagging

Leading

Lagging or leading

⇒ The period of a wave is

The same as frequency

Time required to complete one cycle

Expressed in amperes

None of the above

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is

70.7 A

141.4A

150A

282.8 A

⇒ Form factor is the ratio of

Average value/r.m.s. value

Average value/peak value

r.m.s. value/average value

r.m.s. value/peak value

⇒ Ohm is the unit of all of the following except

Inductive reactance

Capacitive reactance

Resistance

Capacitance

⇒ In a R-L-C series circuit if voltage V across the circuit is reduced to half the current I will change to

2 I

I/2

3/4 I

5/8 I

⇒ In A.C. circuit laminated iron is invariably used in order to

Reduce eddy current loss

Increase heat radiation

Make assembly cheap and easier

Reduce circuit permeability

⇒ The product of apparent power and cosine of the phase angle between circuit voltage and current is

True power

Reactive power

Volt-amperes

Instantaneous power

⇒ In a series resonant circuit, the impedance of the circuit is

Minimum

Maximum

Zero

None of the above

⇒ In A.C. circuit the power curve is a sine wave having

Double the frequency of voltage

Same frequency as that of voltage

Half the frequency of the voltage

None of these

⇒ The peak value of a sine wave is 200 V. Its average value is

127.4V

141.4V

282.8V

200 V

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.

Impedance

Susceptance

Quality factor

Selectivity

⇒ The series element of a band stop filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates

Low efficiency

High power factor

Unity power factor

Maximum Load current

⇒ In an A.C. circuit I sin Φ is called

Active component

Wattless component

Any of the above

None of these