Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | For the same peak value, which of the following wave has the least mean value ? |

A. | Half wave rectified sine wave [Correct Answer] |

B. | Triangular wave [Wrong Answer] |

C. | Sine wave [Wrong Answer] |

D. | Square wave [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ Power factor of the following circuit will be zero

Resistance

Inductance

Capacitance

Both (B) and (C)

⇒ The time constant of a series R-C circuit is given by

R/C

RC

^{2}

RC

R

^{2}C

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.

Impedance

Susceptance

Quality factor

Selectivity

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees

90

60

45

30

⇒ The ratio of active power to apparent power is known as ____ factor.

Demand

Load

Power

Form

⇒ The power factor of incandescent bulb is

0.8 lagging

0.8 leading

Unity

Zero

⇒ The series element of a band stop filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ In A.C. circuit laminated iron is invariably used in order to

Reduce eddy current loss

Increase heat radiation

Make assembly cheap and easier

Reduce circuit permeability

⇒ The peak value of a sine wave is 200 V. Its average value is

127.4V

141.4V

282.8V

200 V

⇒ The voltage of domestic supply is 220 V. This figure represents-

Mean value

r.m.s. value

Peak value

Average value

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates

Low efficiency

High power factor

Unity power factor

Maximum Load current

⇒ In the R - L - C containing R = 4.5ω L = 0.06 H,C = 0.6 µF the power factor will be

Zero

Lagging

Leading

Unity

⇒ The power taken by a 3-Φ load is given by the expression

√3 V

_{L}I

_{L}sinΦ

√3 V

_{L}I

_{L}cosΦ

3 V

_{L}I

_{L}sinΦ

3 V

_{L}I

_{L}cosΦ

⇒ The frequency of domestic power supply in India is

200 Hz

100 Hz

60 Hz

50 Hz

⇒ A resonance curve for a series circuit is a plot of frequency versus

Current

Voltage

Impedance

Reactance

⇒ The time period of a sine wave is 1/50 seconds. Its frequency is

20 Hz

30 Hz

40 Hz

50 Hz

⇒ In a pure resistive circuit

Current lags behind the voltage by 90°

Current leads the voltage by 90°

Current can lead or lag the voltage by 90°

Current is in phase with the voltage

⇒ The r.m.s. value of a half-wave rectified current is 100 A. Its value for full-wave rectification would be____ amperes.

141.4

200

200/π

40/π

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?

0.5A

1.5 A

2A

3A

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is

Apparent power

True power

Reactive power

None of the above

⇒ Which of the following waves has the highest value of peak factor '?

Square wave

Sine wave

Half wave rectifier sine wave

Triangular wave

⇒ The negative maximum of a cosine wave occurs at

30

45

90

180

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is

360°

180°

90°

0°

⇒ The shunt element of prototype high pass filter is

Resistive

Inductive

Capacitive

Combination of L and C

⇒ Form factor for a sine wave is

1.414

0.707

1.11

0.637

⇒ Poor power factor results in all of the following EXCEPT.

Overloading of transformers

Overloading of altemators

Reduction in power losses

Reduction in load handling capacity of electrical system

⇒ The dual of a loop is

Twig

Node pair

Mesh

Tree

⇒ Form factor is the ratio of

Average value/r.m.s. value

Average value/peak value

r.m.s. value/average value

r.m.s. value/peak value

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage

180°

90°

60°

0°