Question is ⇒ If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be, Options are ⇒ (A) 0.001 S, (B) 0.1 S, (C) 10 S, (D) 100 S, (E) , Leave your comments or Download question paper.

Question is ⇒ If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be, Options are ⇒ (A) 0.001 S, (B) 0.1 S, (C) 10 S, (D) 100 S, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be
A.	0.001 S [Wrong Answer]
B.	0.1 S [Correct Answer]
C.	10 S [Wrong Answer]
D.	100 S [Wrong Answer]
View Answer 9 -5 Explanation:- Answer : B Discuss it below : Mehul Vanzara Said on 2020-10-03 21:23:10 Capacitors for power factor correction are rated in !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Power factor of electric bulb is
Zero
Lagging
Leading
Unity

⇒ Poor power factor results in all of the following EXCEPT.
Overloading of transformers
Overloading of altemators
Reduction in power losses
Reduction in load handling capacity of electrical system

⇒ A network is said to be non-linear if it does not satisfy
Homogeneity condition
Superposition condition
Both (A) and (B)
Associative condition

⇒ In a series resonant circuit, the impedance of the circuit is
Minimum
Maximum
Zero
None of the above

⇒ In a series resonant circuit, the impedance of the circuit is
Maximum
Minimum
Zero
Infinite

⇒ The time constant of a series R-C circuit is given by
R/C
RC²
RC
R²C

⇒ While drawing vector diagram for a series circuit the reference vector is
Voltage
Current
Power
Phase angle

⇒ Power factor of the following circuit will be unity
Inductance
Capacitance
Resistance
Both (A) and (B)

⇒ In A.C. circuit laminated iron is invariably used in order to
Reduce eddy current loss
Increase heat radiation
Make assembly cheap and easier
Reduce circuit permeability

⇒ For a sine wave with peak value E_max the average value is
0.636 E_max
0.707 E_max
0.434 E_max
1.414 E_max

⇒ The power factor of a series R-L-C circuit at its half-power points is
Unity
Lagging
Leading
Lagging or leading

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?
Square wave
Half wave rectified sine wave
Triangular wave
Sine wave

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.
Impedance
Susceptance
Quality factor
Selectivity

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?
50V
82.8V
100V
173.2 V

⇒ The shunt element in a band pass filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ Which of the following statement is incorrect ?
Resistance is a passive element
Voltage source is an active element
Conductance is a passive element
Current source is a passive element

⇒ In an A.C. circuit I sin Φ is called
Active component
Wattless component
Any of the above
None of these

⇒ The period of a wave is
The same as frequency
Time required to complete one cycle
Expressed in amperes
None of the above

⇒ In a circuit containing R, L and C, power loss can take place
C only
L only
R only
All of the above

⇒ The dual of a loop is
Twig
Node pair
Mesh
Tree

⇒ The voltage of domestic supply is 220 V. This figure represents-
Mean value
r.m.s. value
Peak value
Average value

⇒ The power is measured in terms of decibles in case of
Electronic equipment
Transformers
Current transformers
Auto-transformers

⇒ The series element of a band stop filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ A parallel resonant circuit can be used
As a high impedance
To reject a small band of frequencies
Both (A) and (B)
To amplify certain frequencies

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is
Apparent power
True power
Reactive power
None of the above

⇒ In a pure resistive circuit
Current lags behind the voltage by 90°
Current leads the voltage by 90°
Current can lead or lag the voltage by 90°
Current is in phase with the voltage

⇒ The time period of a sine wave is 1/50 seconds. Its frequency is
20 Hz
30 Hz
40 Hz
50 Hz

⇒ The power factor of a D.C. circuit is always
Less than unity
Unity
Greater than Unity
Zero

⇒ The ratio of active power to apparent power is known as ____ factor.
Demand
Load
Power
Form

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in
Parallel
Series
Either (A) or (B)
None