Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Higher the Q of a series circuit |

A. | Broader its resonance curve [Wrong Answer] |

B. | Narrower its pass band [Correct Answer] |

C. | Greater its band width [Wrong Answer] |

D. | Sharper its resonace [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is

Apparent power

True power

Reactive power

None of the above

⇒ The negative maximum of a cosine wave occurs at

30

45

90

180

⇒ Higher the Q of a series circuit

Broader its resonance curve

Narrower its pass band

Greater its band width

Sharper its resonace

⇒ The dual of a loop is

Twig

Node pair

Mesh

Tree

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?

50V

82.8V

100V

173.2 V

⇒ The peak value of a sine wave is 200 V. Its average value is

127.4V

141.4V

282.8V

200 V

⇒ A heater is rated as 230 V, 10 KW, AC. The value 230 V refers t

Average voltage

r.m.s. voltage

Peak voltage

None of these

⇒ The power factor of a D.C. circuit is always

Less than unity

Unity

Greater than Unity

Zero

⇒ The r.m.s. value and mean value is the same in the case of

Triangular wave

Sine wave

Square wave

Half wave rectified sine wave

⇒ The power factor at resonance in RLC parallel circuit is

Zero

0.08 Lagging

0.8 Leading

Unity

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in

Parallel

Series

Either (A) or (B)

None

⇒ Poor power factor results in all of the following EXCEPT.

Overloading of transformers

Overloading of altemators

Reduction in power losses

Reduction in load handling capacity of electrical system

⇒ In a series resonant circuit, the impedance of the circuit is

Maximum

Minimum

Zero

Infinite

⇒ In an A.C. circuit I sin Φ is called

Active component

Wattless component

Any of the above

None of these

⇒ The form factor of D.C. supply voltage is always

Zero

0.5

Unity

Infinite

⇒ While drawing vector diagram for a series circuit the reference vector is

Voltage

Current

Power

Phase angle

⇒ The ratio of active power to apparent power is known as ____ factor.

Demand

Load

Power

Form

⇒ The power factor of a series R-L-C circuit at its half-power points is

Unity

Lagging

Leading

Lagging or leading

⇒ In a circuit containing R, L and C, power loss can take place

C only

L only

R only

All of the above

⇒ The shunt element of prototype high pass filter is

Resistive

Inductive

Capacitive

Combination of L and C

⇒ Which of the following is not a non-linear element ?

Transistor

Heater coil

Diode

Electric arc with unlike electrodes

⇒ A resonance curve for a series circuit is a plot of frequency versus

Current

Voltage

Impedance

Reactance

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.

Impedance

Susceptance

Quality factor

Selectivity

⇒ Ohm is the unit of all of the following except

Inductive reactance

Capacitive reactance

Resistance

Capacitance

⇒ In a parallel R-C circuit, the current always ____the applied voltage.

Lags

Leads

Remains in phase with

None of the above

⇒ Which of the following waves has the highest value of peak factor '?

Square wave

Sine wave

Half wave rectifier sine wave

Triangular wave

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?

0.5A

1.5 A

2A

3A

⇒ The series element of a band stop filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ The product of apparent power and cosine of the phase angle between circuit voltage and current is

True power

Reactive power

Volt-amperes

Instantaneous power

⇒ The best place to install a capacitor is

Very near to inductive load

Across the terminals of the inductive load

Far away from the inductive load

Any where