Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Capacitors for power factor correction are rated in |

A. | kW [Wrong Answer] |

B. | kVA [Wrong Answer] |

C. | kV [Wrong Answer] |

D. | kVAR [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A coil with large distributed capacitance has a

High resonant frequency

Low resonant frequency

Low quality factor

Low resistance

⇒ The safest value of current the human body can carry for more than 3 second is

4 mA

9 mA

15 mA

25 mA

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is

360°

180°

90°

0°

⇒ A network is said to be non-linear if it does not satisfy

Homogeneity condition

Superposition condition

Both (A) and (B)

Associative condition

⇒ The value of operator j2 is equal to

Zero

+1

-1

√-1

⇒ Power factor of the following circuit will be zero

Resistance

Inductance

Capacitance

Both (B) and (C)

⇒ The shunt element in a band pass filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ The unit of frequency of an A.C. signal is

Cycle

Cycle-sec

Hertz

Hertz/sec

⇒ A heater is rated as 230 V, 10 KW, AC. The value 230 V refers t

Average voltage

r.m.s. voltage

Peak voltage

None of these

⇒ In a R-L-C series circuit if voltage V across the circuit is reduced to half the current I will change to

2 I

I/2

3/4 I

5/8 I

⇒ Power factor of the following circuit will be unity

Inductance

Capacitance

Resistance

Both (A) and (B)

⇒ Form factor is the ratio of

Average value/r.m.s. value

Average value/peak value

r.m.s. value/average value

r.m.s. value/peak value

⇒ Which of the following circuit component opposes the change in the circuit voltage

Inductance

Capacitance

Conductance

Resistance

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.

Impedance

Susceptance

Quality factor

Selectivity

⇒ For the same peak value of voltage which wave form will have the least r.m.s. value ?

Sine wave

Square wave

Triangular wave

Full wave rectified sine wave

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in

Parallel

Series

Either (A) or (B)

None

⇒ Two sinusoidal quantities are said to be phase quadrature, when their phase difference is

0

30°

45°

90°

⇒ The ratio of active power to apparent power is known as ____ factor.

Demand

Load

Power

Form

⇒ A parallel resonant circuit can be used

As a high impedance

To reject a small band of frequencies

Both (A) and (B)

To amplify certain frequencies

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?

Square wave

Half wave rectified sine wave

Triangular wave

Sine wave

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ Capacitive reactance is more when

Capacitances is less and frequency of supply is less

Capacitance is less and frequency of supply is more

Capacitance is more and frequency of supply is less

Capacitance is more and frequency of supply is more

⇒ In an A.C. circuit I sin Φ is called

Active component

Wattless component

Any of the above

None of these

⇒ What inductance will give the same reactance as a capacitor of 2 µF when both are at 50 Hz?

5 H

10 H

15 H

20 H

⇒ In a purely inductive circuit

Actual power is zero

Reactive power is zero

Apparent power is zero

None of these

⇒ If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be

0.001 S

0.1 S

10 S

100 S

⇒ For the full wave rectified sine wave the r.m.s. value is

0.707 I

_{max}

0.636 I

_{max}

0.318 I

_{max}

Zero

⇒ In a parallel R-C circuit, the current always ____the applied voltage.

Lags

Leads

Remains in phase with

None of the above

⇒ The power taken by a 3-Φ load is given by the expression

√3 V

_{L}I

_{L}sinΦ

√3 V

_{L}I

_{L}cosΦ

3 V

_{L}I

_{L}sinΦ

3 V

_{L}I

_{L}cosΦ

⇒ The voltage of domestic supply is 220 V. This figure represents-

Mean value

r.m.s. value

Peak value

Average value