Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The power consumed in a circuit element will be least when the phase difference between the current and voltage |

A. | 180° [Wrong Answer] |

B. | 90° [Correct Answer] |

C. | 60° [Wrong Answer] |

D. | 0° [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.

Low

Very low

High

Very high

⇒ Inductance affects the direct current flow

Only at the time of turning off

Only at the time of turning on

At the time of turning on and off

At all the time of operation

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ For a sine wave with peak value E

_{max}the average value is

0.636 E

_{max}

0.707 E

_{max}

0.434 E

_{max}

1.414 E

_{max}

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is

Apparent power

True power

Reactive power

None of the above

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is

360°

180°

90°

0°

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage

180°

90°

60°

0°

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates

Low efficiency

High power factor

Unity power factor

Maximum Load current

⇒ In a circuit containing R, L and C, power loss can take place

C only

L only

R only

All of the above

⇒ The voltage of domestic supply is 220 V. This figure represents-

Mean value

r.m.s. value

Peak value

Average value

⇒ Two sinusoidal quantities are said to be phase quadrature, when their phase difference is

0

30°

45°

90°

⇒ Capacitors for power factor correction are rated in

kW

kVA

kV

kVAR

⇒ The shunt element of prototype high pass filter is

Resistive

Inductive

Capacitive

Combination of L and C

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees

90

60

45

30

⇒ The power factor of a D.C. circuit is always

Less than unity

Unity

Greater than Unity

Zero

⇒ The dual of a link is

Twig

Node

Loop

Tree branch

⇒ In a series resonant circuit, the impedance of the circuit is

Maximum

Minimum

Zero

Infinite

⇒ In a series resonant circuit, the impedance of the circuit is

Minimum

Maximum

Zero

None of the above

⇒ A parallel resonant circuit can be used

As a high impedance

To reject a small band of frequencies

Both (A) and (B)

To amplify certain frequencies

⇒ The double energy transient occur in the

Purely inductive circuit

R-L circuit

R-C circuit

R-L-C circuit

⇒ In A.C. circuit laminated iron is invariably used in order to

Reduce eddy current loss

Increase heat radiation

Make assembly cheap and easier

Reduce circuit permeability

⇒ The form factor of D.C. supply voltage is always

Zero

0.5

Unity

Infinite

⇒ The unit of frequency of an A.C. signal is

Cycle

Cycle-sec

Hertz

Hertz/sec

⇒ In a R-L-C series circuit if voltage V across the circuit is reduced to half the current I will change to

2 I

I/2

3/4 I

5/8 I

⇒ The safest value of current the human body can carry for more than 3 second is

4 mA

9 mA

15 mA

25 mA

⇒ While drawing vector diagram for a series circuit the reference vector is

Voltage

Current

Power

Phase angle

⇒ Poor power factor results in all of the following EXCEPT.

Overloading of transformers

Overloading of altemators

Reduction in power losses

Reduction in load handling capacity of electrical system

⇒ The series element of a band stop filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in

Parallel

Series

Either (A) or (B)

None

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?

0.5A

1.5 A

2A

3A