Question is ⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates, Options are ⇒ (A) Low efficiency, (B) High power factor, (C) Unity power factor, (D) Maximum Load current, (E) , Leave your comments or Download question paper.

Question is ⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates, Options are ⇒ (A) Low efficiency, (B) High power factor, (C) Unity power factor, (D) Maximum Load current, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In an A.C. circuit, a low value of kVAR compared with kW indicates
A.	Low efficiency [Wrong Answer]
B.	High power factor [Correct Answer]
C.	Unity power factor [Wrong Answer]
D.	Maximum Load current [Wrong Answer]
View Answer 16 -13 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Form factor for a sine wave is
1.414
0.707
1.11
0.637

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.
Low
Very low
High
Very high

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?
Square wave
Half wave rectified sine wave
Triangular wave
Sine wave

⇒ The power factor of a D.C. circuit is always
Less than unity
Unity
Greater than Unity
Zero

⇒ Power factor of the following circuit will be unity
Inductance
Capacitance
Resistance
Both (A) and (B)

⇒ In a series resonant circuit, the impedance of the circuit is
Maximum
Minimum
Zero
Infinite

⇒ The dual of a link is
Twig
Node
Loop
Tree branch

⇒ The frequency of domestic power supply in India is
200 Hz
100 Hz
60 Hz
50 Hz

⇒ Which of the following is not a non-linear element ?
Transistor
Heater coil
Diode
Electric arc with unlike electrodes

⇒ The double energy transient occur in the
Purely inductive circuit
R-L circuit
R-C circuit
R-L-C circuit

⇒ The shunt element in a band pass filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ The value of operator j2 is equal to
Zero
+1
-1
√-1

⇒ The time constant of a series R-C circuit is given by
R/C
RC²
RC
R²C

⇒ A parallel resonant circuit can be used
As a high impedance
To reject a small band of frequencies
Both (A) and (B)
To amplify certain frequencies

⇒ The power factor of a series R-L-C circuit at its half-power points is
Unity
Lagging
Leading
Lagging or leading

⇒ In A.C. circuit the power curve is a sine wave having
Double the frequency of voltage
Same frequency as that of voltage
Half the frequency of the voltage
None of these

⇒ While drawing vector diagram for a series circuit the reference vector is
Voltage
Current
Power
Phase angle

⇒ In an A.C. circuit power is dissipated in
Resistance only
Inductance only
Capacitance only
None of the above

⇒ The shunt element of prototype high pass filter is
Resistive
Inductive
Capacitive
Combination of L and C

⇒ Ohm is the unit of all of the following except
Inductive reactance
Capacitive reactance
Resistance
Capacitance

⇒ A heater is rated as 230 V, 10 KW, AC. The value 230 V refers t
Average voltage
r.m.s. voltage
Peak voltage
None of these

⇒ The power is measured in terms of decibles in case of
Electronic equipment
Transformers
Current transformers
Auto-transformers

⇒ In A.C. circuit laminated iron is invariably used in order to
Reduce eddy current loss
Increase heat radiation
Make assembly cheap and easier
Reduce circuit permeability

⇒ For the full wave rectified sine wave the r.m.s. value is
0.707 I_max
0.636 I_max
0.318 I_max
Zero

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is
70.7 A
141.4A
150A
282.8 A

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees
90
60
45
30

⇒ The reflection co-efficient of the simplest standing wave is
+1
1
Zero
Infinity

⇒ Which of the following circuit component opposes the change in the circuit voltage
Inductance
Capacitance
Conductance
Resistance

⇒ For 200 V r.m.s. value triangular wave, the peak voltage will be
200 V
222 V
282 V
346 V

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in
Parallel
Series
Either (A) or (B)
None