Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | In a series resonant circuit, the impedance of the circuit is |

A. | Maximum [Wrong Answer] |

B. | Minimum [Correct Answer] |

C. | Zero [Wrong Answer] |

D. | Infinite [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ For 200 V r.m.s. value triangular wave, the peak voltage will be

200 V

222 V

282 V

346 V

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is

360°

180°

90°

0°

⇒ A network is said to be non-linear if it does not satisfy

Homogeneity condition

Superposition condition

Both (A) and (B)

Associative condition

⇒ The value of operator j2 is equal to

Zero

+1

-1

√-1

⇒ In a parallel R-C circuit, the current always ____the applied voltage.

Lags

Leads

Remains in phase with

None of the above

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates

Low efficiency

High power factor

Unity power factor

Maximum Load current

⇒ In a series resonant circuit, the impedance of the circuit is

Minimum

Maximum

Zero

None of the above

⇒ Two sinusoidal quantities are said to be phase quadrature, when their phase difference is

0

30°

45°

90°

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?

0.5A

1.5 A

2A

3A

⇒ The capacitors for power factor correction are rated in terms of

Voltage

VA

kW

kVAR

⇒ If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be

0.001 S

0.1 S

10 S

100 S

⇒ The power is measured in terms of decibles in case of

Electronic equipment

Transformers

Current transformers

Auto-transformers

⇒ Power factor of electric bulb is

Zero

Lagging

Leading

Unity

⇒ Skin effect occurs when a conductor carries current at____ frequencies.

Very low

Low

Medium

High

⇒ Higher the Q of a series circuit

Broader its resonance curve

Narrower its pass band

Greater its band width

Sharper its resonace

⇒ The power factor of incandescent bulb is

0.8 lagging

0.8 leading

Unity

Zero

⇒ A resonance curve for a series circuit is a plot of frequency versus

Current

Voltage

Impedance

Reactance

⇒ In the R - L - C containing R = 4.5ω L = 0.06 H,C = 0.6 µF the power factor will be

Zero

Lagging

Leading

Unity

⇒ Which of the following waves has the highest value of peak factor '?

Square wave

Sine wave

Half wave rectifier sine wave

Triangular wave

⇒ In a purely inductive circuit

Actual power is zero

Reactive power is zero

Apparent power is zero

None of these

⇒ The transient currents are associated with the

Changes in the stored energy in the inductors and capacitors

Impedance of the current

Applied voltage to the circuit

Resistance of the circuit

⇒ In an A.C. circuit power is dissipated in

Resistance only

Inductance only

Capacitance only

None of the above

⇒ The peak value of a sine wave is 200 V. Its average value is

127.4V

141.4V

282.8V

200 V

⇒ The shunt element of prototype high pass filter is

Resistive

Inductive

Capacitive

Combination of L and C

⇒ The form factor of D.C. supply voltage is always

Zero

0.5

Unity

Infinite

⇒ Power factor of the following circuit will be zero

Resistance

Inductance

Capacitance

Both (B) and (C)

⇒ In a pure resistive circuit

Current lags behind the voltage by 90°

Current leads the voltage by 90°

Current can lead or lag the voltage by 90°

Current is in phase with the voltage

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in

Parallel

Series

Either (A) or (B)

None

⇒ The power taken by a 3-Φ load is given by the expression

√3 V

_{L}I

_{L}sinΦ

√3 V

_{L}I

_{L}cosΦ

3 V

_{L}I

_{L}sinΦ

3 V

_{L}I

_{L}cosΦ