Question is ⇒ In A.C. circuit laminated iron is invariably used in order to, Options are ⇒ (A) Reduce eddy current loss, (B) Increase heat radiation, (C) Make assembly cheap and easier, (D) Reduce circuit permeability, (E) , Leave your comments or Download question paper.

Question is ⇒ In A.C. circuit laminated iron is invariably used in order to, Options are ⇒ (A) Reduce eddy current loss, (B) Increase heat radiation, (C) Make assembly cheap and easier, (D) Reduce circuit permeability, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In A.C. circuit laminated iron is invariably used in order to
A.	Reduce eddy current loss [Correct Answer]
B.	Increase heat radiation [Wrong Answer]
C.	Make assembly cheap and easier [Wrong Answer]
D.	Reduce circuit permeability [Wrong Answer]
View Answer 7 -6 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A parallel resonant circuit can be used
As a high impedance
To reject a small band of frequencies
Both (A) and (B)
To amplify certain frequencies

⇒ The r.m.s. value of pure cosine function is
0.5 of peak value
0.707 of peak value
Same as peak value
Zero

⇒ If resistance is 20 ω and inductance is 2H in a RL series circuit, then time constant of this circuit will be
0.001 S
0.1 S
10 S
100 S

⇒ Capacitors for power factor correction are rated in
kW
kVA
kV
kVAR

⇒ The double energy transient occur in the
Purely inductive circuit
R-L circuit
R-C circuit
R-L-C circuit

⇒ For a sine wave with peak value E_max the average value is
0.636 E_max
0.707 E_max
0.434 E_max
1.414 E_max

⇒ The unit of frequency of an A.C. signal is
Cycle
Cycle-sec
Hertz
Hertz/sec

⇒ For the same peak value of voltage which wave form will have the least r.m.s. value ?
Sine wave
Square wave
Triangular wave
Full wave rectified sine wave

⇒ For a sine wave with peak value I_max the r.m.s. value is
0.5 I_max
0.707 I_max
0.9 I_max
1.414 I_max

⇒ The reflection co-efficient of the simplest standing wave is
+1
1
Zero
Infinity

⇒ The time period of a sine wave is 1/50 seconds. Its frequency is
20 Hz
30 Hz
40 Hz
50 Hz

⇒ In a purely inductive circuit
Actual power is zero
Reactive power is zero
Apparent power is zero
None of these

⇒ The ratio of active power to apparent power is known as ____ factor.
Demand
Load
Power
Form

⇒ The power is measured in terms of decibles in case of
Electronic equipment
Transformers
Current transformers
Auto-transformers

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates
Low efficiency
High power factor
Unity power factor
Maximum Load current

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.
Low
Very low
High
Very high

⇒ Two sinusoidal quantities are said to be phase quadrature, when their phase difference is
0
30°
45°
90°

⇒ Higher the Q of a series circuit
Broader its resonance curve
Narrower its pass band
Greater its band width
Sharper its resonace

⇒ The power factor of incandescent bulb is
0.8 lagging
0.8 leading
Unity
Zero

⇒ While drawing vector diagram for a series circuit the reference vector is
Voltage
Current
Power
Phase angle

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees
90
60
45
30

⇒ For 200 V r.m.s. value triangular wave, the peak voltage will be
200 V
222 V
282 V
346 V

⇒ The voltage of domestic supply is 220 V. This figure represents-
Mean value
r.m.s. value
Peak value
Average value

⇒ For the same peak value, which of the following wave has the least mean value ?
Half wave rectified sine wave
Triangular wave
Sine wave
Square wave

⇒ In a pure resistive circuit
Current lags behind the voltage by 90°
Current leads the voltage by 90°
Current can lead or lag the voltage by 90°
Current is in phase with the voltage

⇒ Poor power factor results in all of the following EXCEPT.
Overloading of transformers
Overloading of altemators
Reduction in power losses
Reduction in load handling capacity of electrical system

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?
0.5A
1.5 A
2A
3A

⇒ The safest value of current the human body can carry for more than 3 second is
4 mA
9 mA
15 mA
25 mA

⇒ The r.m.s. value and mean value is the same in the case of
Triangular wave
Sine wave
Square wave
Half wave rectified sine wave

⇒ A coil with large distributed capacitance has a
High resonant frequency
Low resonant frequency
Low quality factor
Low resistance