Question is ⇒ The power factor of incandescent bulb is, Options are ⇒ (A) 0.8 lagging, (B) 0.8 leading, (C) Unity, (D) Zero, (E) , Leave your comments or Download question paper.

Question is ⇒ The power factor of incandescent bulb is, Options are ⇒ (A) 0.8 lagging, (B) 0.8 leading, (C) Unity, (D) Zero, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The power factor of incandescent bulb is
A.	0.8 lagging [Wrong Answer]
B.	0.8 leading [Wrong Answer]
C.	Unity [Correct Answer]
D.	Zero [Wrong Answer]
View Answer 22 -10 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The dual of a loop is
Twig
Node pair
Mesh
Tree

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage
180°
90°
60°
0°

⇒ Skin effect occurs when a conductor carries current at____ frequencies.
Very low
Low
Medium
High

⇒ Capacitors for power factor correction are rated in
kW
kVA
kV
kVAR

⇒ The reflection co-efficient of the simplest standing wave is
+1
1
Zero
Infinity

⇒ In A.C. circuit laminated iron is invariably used in order to
Reduce eddy current loss
Increase heat radiation
Make assembly cheap and easier
Reduce circuit permeability

⇒ The shunt element in a band pass filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ In A.C. circuit the power curve is a sine wave having
Double the frequency of voltage
Same frequency as that of voltage
Half the frequency of the voltage
None of these

⇒ The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of____ degrees
90
60
45
30

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?
Square wave
Half wave rectified sine wave
Triangular wave
Sine wave

⇒ In a series resonant circuit, the impedance of the circuit is
Maximum
Minimum
Zero
Infinite

⇒ The unit of frequency of an A.C. signal is
Cycle
Cycle-sec
Hertz
Hertz/sec

⇒ A heater is rated as 230 V, 10 KW, AC. The value 230 V refers t
Average voltage
r.m.s. voltage
Peak voltage
None of these

⇒ The time constant of a series R-C circuit is given by
R/C
RC²
RC
R²C

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates
Low efficiency
High power factor
Unity power factor
Maximum Load current

⇒ The double energy transient occur in the
Purely inductive circuit
R-L circuit
R-C circuit
R-L-C circuit

⇒ The ratio of active power to apparent power is known as ____ factor.
Demand
Load
Power
Form

⇒ While drawing vector diagram for a series circuit the reference vector is
Voltage
Current
Power
Phase angle

⇒ Power factor of an inductive circuit is usually improved by connecting capacitor to it in
Parallel
Series
Either (A) or (B)
None

⇒ Form factor is the ratio of
Average value/r.m.s. value
Average value/peak value
r.m.s. value/average value
r.m.s. value/peak value

⇒ The voltage of domestic supply is 220 V. This figure represents-
Mean value
r.m.s. value
Peak value
Average value

⇒ The frequency of domestic power supply in India is
200 Hz
100 Hz
60 Hz
50 Hz

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.
Impedance
Susceptance
Quality factor
Selectivity

⇒ The negative maximum of a cosine wave occurs at
30
45
90
180

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is
70.7 A
141.4A
150A
282.8 A

⇒ In an A.C. circuit I sin Φ is called
Active component
Wattless component
Any of the above
None of these

⇒ In a pure resistive circuit
Current lags behind the voltage by 90°
Current leads the voltage by 90°
Current can lead or lag the voltage by 90°
Current is in phase with the voltage

⇒ Poor power factor results in all of the following EXCEPT.
Overloading of transformers
Overloading of altemators
Reduction in power losses
Reduction in load handling capacity of electrical system

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?
50V
82.8V
100V
173.2 V

⇒ The capacitors for power factor correction are rated in terms of
Voltage
VA
kW
kVAR