Question is ⇒ Microwave link repeaters are typically 50 km apart in TV transmission due to, Options are ⇒ (A) atmosphere attenuation, (B) output power tube limitations, (C) attenuation of surface wave, (D) earth's curvature, (E) , Leave your comments or Download question paper.

Question is ⇒ Microwave link repeaters are typically 50 km apart in TV transmission due to, Options are ⇒ (A) atmosphere attenuation, (B) output power tube limitations, (C) attenuation of surface wave, (D) earth's curvature, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Microwave link repeaters are typically 50 km apart in TV transmission due to
A.	atmosphere attenuation [Wrong Answer]
B.	output power tube limitations [Wrong Answer]
C.	attenuation of surface wave [Wrong Answer]
D.	earth's curvature [Correct Answer]
View Answer 2 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The analog signal given below is sampled by 600 samples per se
600 Hz
120 Hz
300 Hz
360 Hz

⇒ A very reliable service has to be established between two points on earth separated by 1000 km. The band that will be used as
MF
VHF
VLF
HF

⇒ For the time domain response shown in figure the
lies in left half plane
lies on imaginary axis
lies along the positive real axis
may be complex or imaginary

⇒ Which one is correct?
Sky wave propagation (2 to 30 MHz)
Space wave propagation (> 30 MHz)
Tropospheric propagation (> 300 MHz)
All of the above

⇒ Which of the following is a valid integer constant?
127
127
127
125 + 3

⇒ Modulated carrier power in FM
increases with modulating signal power
decreases with modulating signal power
is independent of the modulating signal power
none

⇒ In a JFET the width of channel is controlled by
gate voltage
drain current
source current
all of the above

⇒ Poynting vector signifies which of the following?
Power density vector producing electrostatic field
Power density vector producing electromagnetic field
Current density vector producing electrostatic field
Current density vector producing electromagnetic field

⇒ Which of the following is correct in FORTRAN 77?
PARAMETER PMOS = 9.8, NMOS = X
PARAMETER (PMOS = 9.8, NMOS = X)
PARAMETER PMOS = 9.8, NMOS = X
PARAMETER PMOS, NMOS = 9.8, X

⇒ Figure represen
JFET shunt switching circuit
JFET series switching circuit
JFET analog switch
multiplexing

⇒ In a positive edge triggered D flip flop
D input is called direct set
Preset is called direct reset
Present and clear are called direct set and reset respectively
D input overrides other inputs

⇒ A single phase half wave regulator uses
2 diodes and 2 thyristors
2 thyristors
1 diode and 1 thyristor
2 diodes

⇒ The MOS symbol shown indicates that

It is depletion type
It is enhancement type
It is channel
It is P-channel
Electrons flow from s to D
Holes flow from D to s

The true statements
1, 3, 6
1, 3, 5
2, 4, 6
2, 3, 5

⇒ Which one of the following statements is not a property of RL driving point impedance?
The first critical frequency at the origin is a zero
The last critical frequency is a pole
The impedance at S = ∞ always less than the impedance at S = zero
The slope of the impedance curve is positive at all points

⇒

Assertion (A): In microprocessor 8085 instruction LXIB, 90 FF H means register B and C are loaded with upper and lower bytes to get B = 90 H and C = FFH.

Reason (R): In 8085 the stack pointer indicates which memory location is to accessed.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒

Assertion (A): When a PID controller is added to a system, the peak overshoot to step input cannot be determined easily.

Reason (R): Use of PID controller introduces a zero in the forward path.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ The disadvantage of FM over AM is that
high output power is needed
high modulating power is needed
noise is very high for high frequency
large bandwidth is required

⇒ An RLC series circuit has R = 8 Ω, X_L = 8 Ω and X_C = 8 Ω Its impedance is
8 + j 16 Ω
8 + j 8 Ω
8 Ω
24 Ω

⇒ A moving iron voltmeter reads 250 V when connected to 250 V dc. If connected to 250 V 50 Hz, the voltmeter reading is likely to be
250 V
252 V
248 V
210 V

⇒ A pure tone at 1000 Hz has a dB level of 50 dB. If two such tones exist simultaneously the dB level is about
50 dB
53 dB
100 dB
200 dB

⇒ Instruction cycle is the time required to complete the execution of an instruction.
TRUE
FALSE

⇒

Assertion (A): The phase angle plot in Bode diagram is not affected by change in system gain.

Reason (R): The variation in gain has no effect on phase margin of the system.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ Pick out the odd one
stochastic variable
stochastic function
random variable
random experiment

⇒ An increase in temperature increases the width of depletion layer.
TRUE
FALSE

⇒ In attenuation band, β is an odd multiple of p.
TRUE
FALSE

⇒ Which of the following materials has the highest electrical conductivity?
Steel
Silver
Aluminium
Zinc

⇒ Which of the following is invalid integer variable name in Fortran?
IAEG
I 124
AILG
MI AC

⇒ It is required to measure the true open circuit emf of a battery. The best device is
dc voltmeter
ammeter and known resistance
dc potentiometer
either (a) or (c)

⇒ A transmission line discontinuity is defined as any interruption in the uniformity of the line.
TRUE
FALSE

⇒ The effective channel length of a MOSFET in saturation decreases with increase in
gate voltage
drain voltage
source voltage
body voltage