Question is ⇒ The relation between the apparent power, actual power and reactive power is given by, Options are ⇒ (A) Apparent power = actual power + reactive power, (B) Apparent power = actual power - reactive power, (C) Apparent power = (actual power)2 - (reactive power)2, (D) Apparent power = (actual power)2 + (reactive power)2, (E) , Leave your comments or Download question paper.

Question is ⇒ The relation between the apparent power, actual power and reactive power is given by, Options are ⇒ (A) Apparent power = actual power + reactive power, (B) Apparent power = actual power - reactive power, (C) Apparent power = (actual power)2 - (reactive power)2, (D) Apparent power = (actual power)2 + (reactive power)2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The relation between the apparent power, actual power and reactive power is given by
A.	Apparent power = actual power + reactive power [Wrong Answer]
B.	Apparent power = actual power - reactive power [Wrong Answer]
C.	Apparent power = (actual power)² - (reactive power)² [Wrong Answer]
D.	Apparent power = (actual power)² + (reactive power)² [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Consider the following statements: The radar pulse must be flat topped to

allow accurate range measurement
allow good minimum range
prevent frequency changes in magnetron
make the returned echoes easier to distinguish from noise.

Which of the above are correct?
1, 2, 3, 4
1, 2, 3
1, 2
1, 3, 4

⇒ If R(t) is autocorrelation of a waveform v(t) and R(0) is autocorrelation for t = 0, then
R(0) > R(t)
R(0) ≥ R(t)
R(0) < R(t)
R(0) ≤ R(t)

⇒ In a p-n-p transistor the main current carriers and the mechanism of flow respectively are
electrons, drift
holes, drift
holes, diffusion
electrons, diffusion

⇒ The noise performance of a square law demodulator of AM signal is
better than that of an envelope detector
better than that of a synchronous detector
identical with that of a synchronous detector
poorer than that of an envelope detector

⇒ The maximum permissible distance between two samples of a 10 kHz signal
100 μ sec
50 μ sec
10 μ sec
none

⇒ During transmission over a communication channel, bit errors occur independently with probability P. If a block of n bits is transmitted, the probability of at most one bit error is equal to
1 - (1 - P)ⁿ
P + (n - 1) (1 - P)
nP (1 - P)^{n - 1}
(1 - P)ⁿ + nP (1 - P)^{n - 1}

⇒ The sensitivity of human eyes is maximum at
white portion of spectrum
green portion of spectrum
red portion of spectrum
violet portion of spectrum

⇒ A quantization error is an essential aspect of ADC
TRUE
FALSE

⇒

Match the following:

	List I (Microwave device)		List II (Application)
A.	PIN diode	1.	Microwave amplification
B.	GaAs MOSFET	2.	Low noise microwave generation
C.	Transferred electron device	3.	Electronic tuning of MW oscillator
D.	Varactor diode	4.	Light wave detection

A-1, B-2, C-4, D-3
A-4, B-1, C-2, D-3
A-2, B-3, C-1, D-4
A-3, B-4, C-2, D-1

⇒ Which of the following refers to SSB suppressed carrier amplitude modulated system?
A3E
H3E
J3E
C3F

⇒ If the characteristic equation is (λ + 1) (λ + 2) (λ + 3) = 0, the eigen values are
-1, -2, -3
1, 2, 3
0, 1, 2
0, 2, 3

⇒ The duty cycle of a radar transmitter is equal to
(PRF) (pulse width)
(PRF)/(pulse width)
(pulse width)/(PRF)
(pulse width) + (PRF)

⇒ For an illumination control circuit it is advisable to use a matched TRIAC-DIAC pair.
TRUE
FALSE

⇒ Which of the following are useful in comparing the noise performance of receivers?

Input noise voltage
Noise figure
Noise resistance
Noise temperature

Select answer as per the following codes:
1, 2 and 3
1, 3 and 4
2, 3, 4
1, 2, 4

⇒ In a single phase half wave ac regulator feeding a resistive load, the rms load current
is always positive
may be positive or negative
is always negative
can be even zero

⇒ A dc chopper V = 500 V feeds an electric fraction dc series motor. The chopping frequency is 400 Hz. The series inductance required to limit the maximum current swing to 10 A is
20 mH
about 31 mH
about 51 mH
about 92 mH

⇒ An image uses 512 x 512 picture elements. Each of the picture elements can take any of the 8 distinguishable intensity levels. The maximum entropy in the above image will be
2097152 bits
786432 bits
648 bits
144 bits

⇒ To neglect a current source the terminals across the source are
replaced by some resistance
replaced by capacitance
open-circuited
short-circuited

⇒ Two coils having self inductances of 10 mH and 40 mH are mutually coupled. The maximum possible mutual inductance is
40 mH
20 mH
10 mH
5 mH

⇒ At a given probability of error, binary coherent FSK is interior to binary coherent PSK by
6 dB
3 dB
2 dB
0 dB

⇒ In figure the phase
will be 90° at ω = 0 and 0° at ω = ∞
will be 0° at ω = 0 and 90° at ω = ∞
will be 45° at ω = 0 and 0° at ω = ∞
will be 45° at ω = 0 and 90° at ω = ∞

⇒ A two branch parallel tuned circuit has 100 Ω resistance and 0.1 H inductance in one branch and 10^-6 F capacitor in the other. At resonance frequency, the dynamic resistance is
10 Ω
100 Ω
1000 Ω
10000 Ω

⇒ A choke coil of resistance R and inductance L is shunted by capacitor C. The dynamic resistance is
R/LC
C/RL
L/RC
1/RLC

⇒ The energy of highest value of Autocorrelation of a function 100 cos 50 pt is
50
10
200
zero

⇒ The materials not having negative temperature coefficient of resistivity are
metals
semiconductors
insulators
none of the above

⇒ The expression A ** B / C + D is equivalent to
AB / C + D
AB / C + D
AB / (C + D)
None of the above

⇒ Wienbridge oscillator uses
-ve feedback
+ve feedback
both +ve, -ve feedback
feedback is not required

⇒ Voltage V_L in the circuit when V_s < 0 where D is an ideal diode. (Take R₁ = R_s = R_L = 1 &o
0
1
1.5
cannot find

⇒ PAM stands for
Pulse Analogue Modulation
Phase Analogue Modulation
Pulse Amplitude Modulation
Phase Amplitude Modulation

⇒ In a micro computer the control bus
transmits and receives control signals between processor and other devices
transmits and receives control signals, also sends and receives data
transmits and receives control signals, sends and receives data and transmits address of the device
none of the above