Question is ⇒ The fuse material used in electrical lines must have which one of the following properties?, Options are ⇒ (A) High resistivity, (B) Low conductivity, (C) High melting point, (D) Low melting point, (E) , Leave your comments or Download question paper.

Question is ⇒ The fuse material used in electrical lines must have which one of the following properties?, Options are ⇒ (A) High resistivity, (B) Low conductivity, (C) High melting point, (D) Low melting point, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The fuse material used in electrical lines must have which one of the following properties?
A.	High resistivity [Wrong Answer]
B.	Low conductivity [Wrong Answer]
C.	High melting point [Wrong Answer]
D.	Low melting point [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Read the following statements

The circuitry of ripple counter is more complex than that of synchronous counter.
The maximum frequency of operation of ripple counter depends on the modulus of the counter.
The maximum frequency of operation of synchronous counter does not depend on the modulus of the counter.

Which of the above statements are correct?
1 only
1, 2
1, 2, 3
2, 3

⇒ In the signal flow graph of figure below, the gain C/R will
43048
22/15
24/23
44/23

⇒ A thermistor is a
thermocouple
thermometer
miniature resistance
heat sensitive explosive

⇒ In AM, the modulation envelope has a peak value double the unmodulated carrier level, when the modulation is
0.25
0.33
0.5
1

⇒ The maximum concentration of the element which can be dissolved in solid silicon at a given temperature is termed as
Solid solubility
Dissolution coefficient
Solidification index
Concentration index

⇒ Self bias is an example of __________ feedback that tends to stabilize the drain current against changes in temperature and JFET replacement.
variable
low
negative
positive

⇒ Calculate the electrostatic force of repulsion between two mica particles at a distance of 10^-13 m from each other. Charge on a particle is 3.2 x 10^-19 C. (relative permittivity for mica is 5)
1.843 x 10^-15 N
9.2 x 10^-2 N
14.41 x 10^-9 N
none of these

⇒ In a oscillator, a sine wave generator starts at t = 0. It consist of
Pure sine wave
Pure cosine wave
Unity for t > 0
2∪(t) - 1

⇒ Consider the CMOS circuit shown, where the gate voltage V_G of the n-MOSEFT is increased from zero, while the gate voltage of the p-MOSFET is kept constant at 3 V. Assume that, for both transistor, the magnitude of the threshold voltage is 1 V and the product of the transconductor parameter and the (W/L) ratio, i.e. the quality μC_0x(W/L), is 1mA. V^{-2Both the MOSFET are in saturation region
Both the MOSFET are in triode region
n-MOSFET is in triode and p-MOSFET is in saturation region
n-MOSFET is in saturation and p-MOSFET is in triode region}

⇒ In a single phase full wave converter (M - 2 connection) feeding a highly inductive load, the firing angle for each thyristor is a in the respective half cycle. The period of conduction of each thyristor is
p - a
p
p + a
p - 2a

⇒ The reason for glitches on the outputs of decoding gates on a synchronous counter is
FFs changing states together
FFs changing states one at a time
AND gates not functioning properly
none of the above

⇒ Electric lines of force do not cross each other because
the lines of force mutually repel each other
the lines of force emanate from a point charge
the tangent to the line of force gives the direction of E and if they cross two tangents for E which is not possible
none of the above

⇒ An impulse train is
a number of pulses
a number of pulses spaced from each other
a number of pulses all originating together
none of the above

⇒ If the p and T circuits in figure are equivalent, then R₁, R₂, R₃ respectively
9 Ω, 6 Ω, 6 Ω
6 Ω, 6 Ω, 9 Ω
9 Ω, 6 Ω, 9 Ω
6 Ω, 9 Ω, 6 Ω

⇒ What is the purpose of using ALE signal high?
To latch low order address from bus to separate A₀ - A₇ lines
To latch data D₀ - D₇ from bus to separate data bus
To disable data bus latch
All of the above

⇒ Which of the following can act as error detecting devices

a pair of potentiometers
a pair of synchros
a differential transformer
a metadyne
a control transformer

Select the answer using the following codes:
1, 2, 5
2, 3, 4, 5
1, 3, 4, 5
1, 2, 3, 4

⇒ In the graphical analysis of an amplifier circuit, the slope of dc load line depends on
load resistance only
collector supply voltage only
both load resistance and collector supply voltage
none of the above

⇒

Match the following:

	List I		List II
A.	TTL	1.	Low propagation delay
B.	ECL	2.	Low power consumption
C.	MOS	3.	High packing density
D.	CMOS	4.	Saturated bipolar logic

A-4, B-1, C-3, D-2
A-4, B-3, C-1, D-2
A-4, B-3, C-2, D-1
A-3, B-1, C-4, D-2

⇒ In which n type device does p substrate extend upto silicon dioxide layer?
JFET
Depletion type MOSFET
Enhancement type MOSFET
Both (b) and (c)

⇒ The percentage saving in power when the carrier and one of the sidebands are suppressed in an AM wave modulated to a depth of 100% will be nearly
0.5
0.66
0.75
0.83

⇒ MS outlook is a software for DTP.
TRUE
FALSE

⇒ Vectored interrupt is an interrupt that takes the program to a vector location. TRAP vectors to 0024 FI, RST 7.5 to 003 CH, RST 6.5 to 0034 H and
RST 5.5
RST 6.5
24 H to 48 H
RST 5.5 to 002 CH

⇒ In a second order system, the time constant t of exponential envelopes depends
only on damping factor
only on natural frequency
both on damping factor and natural frequency
neither on damping factor nor on natural frequency

⇒ The chip 8259 is a
programmable interrupt controller
programmable peripheral interface
I/O device
memory chip

⇒ Which of the following bridges is also used in an oscillator?
Maxwell
Schering
Hay
Wien

⇒ Slotted line can be used for measurement of high frequencies
TRUE
FALSE

⇒ In the sale of diamonds the unit of weight is carat. One carat is equal to
100 mg
150 mg
200 mg
500 mg

⇒ What are the values of E_max and E_min displayed on the oscilloscope, when a 1 kV P-P carries is modulated to 50%?
2 kV, 0.5 kV
1 kV, 0.5 kV
0.75 kV, 0.25 kV
0.5 kV, 1.5 kV

⇒

Assertion (A): Schottky transistors are preferred over normal transistors in digital circuits

Reason (R): A Schottky transistor when used as a switch, between cutoff and active region.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ One of the advantages of base modulation over collector modulation of a transistor class C amplifier is
improved efficiency
better linearity
high power output per transistor
the lower modulating power requirement