Question is ⇒ What is the address space of 8086 CPU?, Options are ⇒ (A) One Megabyte, (B) 256 Kilobytes, (C) 1 K Megabytes, (D) 64 Kilobytes, (E) , Leave your comments or Download question paper.

Question is ⇒ What is the address space of 8086 CPU?, Options are ⇒ (A) One Megabyte, (B) 256 Kilobytes, (C) 1 K Megabytes, (D) 64 Kilobytes, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	What is the address space of 8086 CPU?
A.	One Megabyte [Correct Answer]
B.	256 Kilobytes [Wrong Answer]
C.	1 K Megabytes [Wrong Answer]
D.	64 Kilobytes [Wrong Answer]
View Answer 1 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In microwave system the function of mode filter is
to suppress modes with lower cut off frequencies
to suppress modes with higher cut off frequencies
to change mode of wave transmission
both (b) and (c)

⇒ In the above case if another sine wave corresponding to 40% modulation is transmitted simultaneously, the total radiated power will be
9.9 kW
10.15 kW
10.84 kW
18.4 kW

⇒ What is the address space of 8086 CPU?
One Megabyte
256 Kilobytes
1 K Megabytes
64 Kilobytes

⇒ The number of PM radio channels which can be accommodated in a spectrum of 300 MHz is about
10
100
500
1500

⇒ If f_s be the signal frequency and f_i be the intermediate frequency then image frequency is given by
f_s + f_i
f_s ± f_i
f_s ± 2f_i
f_s + 2f_i

⇒ If 10 V is the peak voltage across the secondary of the transformer in a half wave rectifier (without any filter circuit), then the maximum voltage on the reverse biased diode will be
20 V
14.14 V
10 V
7.8 V

⇒ In the network of figure, the voltage drops across R₁, R₂, R₃ are 6 V, 8 V and 12 V with polarities as shown. The value of R_{312 Ω
8 Ω
5 Ω
3 Ω}

⇒ Peak to peak value of a sine wave is equal to twice the peak value
TRUE
FALSE

⇒ Consider the following statements

The effect of feedback is to reduce system error
Feedback increases the system gain at one frequency but reduces the system gain as another frequency
Feedback can cause an originally stable system to become unstable

Which of the above statements are correct?
1, 2, 3
1, 2
2, 3
1, 3

⇒ As frequency is increased, the skin effect
increases
decreases
remains the same
either (b) or (c)

⇒ When diodes are connected in series to increase voltage rating the peak inverse voltage per junction
should not exceed half the breakdown voltage
should not exceed the breakdown voltage
should not exceed one third the breakdown voltage
may be equal to or less than breakdown voltage

⇒ A non-inverting voltage feedback amplifier is a
voltage amplifier
current amplifier
current to voltage converter
voltage to current converter

⇒ A 14 pin AND gate IC has __________ AND gates.
8
6
4
2

⇒ Dielectric loss due to polarisation occurs in
bipolar dielectrics
non-metallic dielectrics
liquid dielectrics
all of the above

⇒ For broadside array, maxima will be obtain at
90°, 270°
180°
45°
at any angle

⇒

Assertion (A): When the performance of a stable second order system is improved by a PID controller, the system may become unstable.

Reason (R): PID controller increases the order of the system to 3.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒

Match the following:

	List I		List II
A.	PMMC	1.	Square law type scale
B.	Moving iron	2.	Very good response
C.	Thermo-couple	3.	Linear scale
D.	Electrostatic	4.	Voltmeter

A-4, B-1, C-2, D-3
A-3, B-2, C-1, D-4
A-4, B-2, C-1, D-3
A-3, B-1, C-2, D-4

⇒ The magnitude plot of a rational transfer function G(s) with real coefficients is shown below. Which of the following compensators has such a magnitude p
Lead compensator
Lag compensator
PID compensator
Lead-lag compensator

⇒ The triangular wave of the given figure can be written as v(t) = u(t) - tu(t) + (t - 1) u(t
TRUE
FALSE

⇒ The relation AD - BC = 1 where A, B, C, D are transmission parameters of a network is valid for
every network
passive but not reciprocal network
passive and reciprocal network
both active and passive networks

⇒ For the power amplifier circuit shown below, the maximum power dissipated by both output transisto
9.66 W
30.11 W
31.66 W
33.66 W

⇒ In Bode analysis the correction at corner frequency is 3 dB.
TRUE
FALSE

⇒ SSB stands for
Single Side Band
Suppressed Side Band
Single Sound Band
Single Sky Band

⇒ The analog signal given below is sampled by 600 samples per se
600 Hz
120 Hz
300 Hz
360 Hz

⇒ When satellite radio beam is aimed towards earth, it illuminates on the earth for an oval shaped area called
foot print
beam area
satellite service area
radiated area

⇒ Multiplexer can be used as logic function generator.
TRUE
FALSE

⇒

Match the following:

	List I (type of controller)		List II (Operation)
A.	Pneumatic controller	1.	Flexible operation
B.	Hydraulic controller	2.	High torque high speed operation
C.	Electronic controller	3.	Fire and explosion proof operation

A-1, B-3, C-2
A-1, B-2, C-3
A-3, B-1, C-2
A-3, B-2, C-1

⇒ The dynamic characteristics of capacitive transducer are similar to those of
LP filter
HP filter
notch filter
band stop filter

⇒ The 'h' parameters of the circuit shown in the figure are h_ib = 25 Ω, h_fb = 0.999 and h_ob = 10^-6Ω The Voltage gai
0.99
1.98
2
4

⇒ CMRR is the ratio of differential voltage gain to common mode gain.
TRUE
FALSE