Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The deformation of a spring produced by a unit load is called |

A. | stiffness [Wrong Answer] |

B. | flexibility [Correct Answer] |

C. | influence coefficient [Wrong Answer] |

D. | unit strain [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :Himanshu Gupta Said on 2019-07-04 05:15:14stiffness and flexibility are opposite of each other. !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The fixed support in a real beam becomes in the conjugate beam a

roller support

hinged support

fixed support

free end

⇒ Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have

high shrinkage

less strength

both (a) and (b)

none of above

⇒ Which of the following will give higher ratio of brickwork strength to mortar strength ?

1 : % : 3

1 : Vz: 4>/2

1:1:6

1:2:9

⇒ For masonry work with solid bricks, consistency of mortar should be

5 to 8 cm

9 to 13 cm

14 to 18 cm

19 to 23 cm

⇒ The carryover factor in a prismatic member whose far end is fixed is

0

1/2

3/4

1

⇒ Direct load carrying capacity of a brick masonry wall standing freely as against when it supports RC slab will be

more

less

the same in both the cases

100%

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by

m + r + 2j

m - r + 2j

m + r - 2j

m + r - 3j

⇒ A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear height between RCC slabs at top and bottom. The slenderness ratio of the wall is

15

19

20

25

⇒ Water retentivity for brick masonry should not be less than

50%

60%

70%

80%

⇒ Bending moment at any section in a conjugate beam gives in the actual beam

slope

curvature

deflection

bending moment

⇒ The degree of static indeterminacy up to which column analogy method can be used is

2

3

4

unrestricted

⇒ The method of moment distribution in structural analysis is

An iterative method

An exact method

An approximate method

None of these

⇒ Castigliano's first theorem is applicable

for statically determinate structures only

when the system behaves elastically

only when principle of superposition is valid

none of the above

⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies

less than the left half span

whole of left half span

more than the left half span

whole span

⇒ Which of the following methods of structural analysis is a displacement method ?

moment distribution method

column analogy method

three moment equation

none of the above

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by

2j - r

j - 2r

3j - r

2j + r

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as

sum of thickness of both leaves

two-third of the sum of thickness of both the leaves

actual thickness of the stronger leaf

larger of (b) and (c)

⇒ The ratio between the stress produced in a bar by a sudden applicaiton of load on compared to the stress produced by the gradual application of same load is

1.5

2.0

2.5

3.0

⇒ The moment distribution method in structural analysis can be treated as

Force method

Displacement method

Flexibility method

None of these

⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is

unstable

stable and statically determinate

stable and statically indeterminate

none of the above

⇒ When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that

the head of the load reaches the section

the tail of the load reaches the section

the load position should be such that the section divides it equally on both sides

the load position should be such that the section divides the load in the same ratio as it divides the span

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of

1.2

1.4

1.6

2.0

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is

0.15 MPa

0.125 MPa

0.1 MPa

0.075 MPa

⇒ For strengthening a 50 m long and 5 m high straight compound wall built in brick work, which one of the following would be most suitable?

providing buttresses at certain intervals

providing a deeper foundation

using a richer mortar

using stronger bricks

⇒ In the displacement method of structural analysis, the basic unknowns are

displacements

force

displacements and forces

none of the above

⇒ The torsional stiffness of a member can be defined as

Torque for unit moment

Torque for unit twist

Moment for unit twist

Torsion for unit twist

⇒ The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in

vertical direction

horizontal direction

inclined direction

the direction in which the deflection is required

⇒ The Castigliano's second theorem can be used to compute deflections

in statically determinate structures only

for any type of structure

at the point under the load only

for beams and frames only

⇒ The three moments equation is applicable only when

the beam is prismatic

there is no settlement of supports

there is no discontinuity such as hinges within the span

the spans are equal

⇒ Unequal settlements in the supports of a statically indeterminate structure develop

Member forces

Reactions from supports

No reactions

Strains in some members only