Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in |

A. | vertical direction [Wrong Answer] |

B. | horizontal direction [Wrong Answer] |

C. | inclined direction [Wrong Answer] |

D. | the direction in which the deflection is required [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is

0.16 Wl

0.20 Wl

0.24 Wl

0.25 Wl

⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is

unstable

stable and statically determinate

stable and statically indeterminate

none of the above

⇒ A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear height between RCC slabs at top and bottom. The slenderness ratio of the wall is

15

19

20

25

⇒ The three moment equation in structural analysis is basically a

Stiffness method

Displacement method

Energy method

Flexibility method

⇒ Water retentivity for brick masonry should not be less than

50%

60%

70%

80%

⇒ The number of independent equations to be satisfied for static equilibrium of a plane structure is

1

2

3

6

⇒ The thickness of each leaf of a cavity wall shall not be less than

5 cm

7.5 cm

10 cm

15 cm

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is

0.15 MPa

0.125 MPa

0.1 MPa

0.075 MPa

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by

m + r + 2j

m - r + 2j

m + r - 2j

m + r - 3j

⇒ The width of the analogous column in the method of column analogy is

2/EI

1/EI

1/2 EI

1/4 EI

⇒ Direct load carrying capacity of a brick masonry wall standing freely as against when it supports RC slab will be

more

less

the same in both the cases

100%

⇒ The analysis of statically indeterminate structures by the unit load method is based on

Consistent deformation

Stiffness method

Consistent force

None of these

⇒ Select the correct statement

Flexibility matrix is a square symmetrical matrix

Stiffness matrix is a square symmetrical matrix

both (a) and (b)

none of the above

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder

always occurs at center of span

always occurs under a wheel load

never occurs under a wheel load

none of the above

⇒ The stiffness method in structural analysis is also known as

Unit load method

Consistent deformation method

Force method

Displacement method

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of

0.4 kg/cm2

0.7 kg/cm2

1.0 kg/cm2

1.2 kg/cm2

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?

5 mm

0.5 mm

0.05 mm

0.005mm

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as

sum of thickness of both leaves

two-third of the sum of thickness of both the leaves

actual thickness of the stronger leaf

larger of (b) and (c)

⇒ In moment distribution method, the sum of distribution factors of all the members meeting at any joint is always

zero

less than 1

1

greater than 1

⇒ Weaker mortar. Of these statements

2 and 3 are correct

1 and 2 are correct

1 and 3 are correct

1, 2 and 3 are correct

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by

2j - r

j - 2r

3j - r

2j + r

⇒ In plastic analysis the shape factor for a circular section is

1.5

1.6

1.7

1.75

⇒ In moment distribution method the sum of distribution factors of all the members meeting at any joint is always

Zero

< 1

> 1

= 1

⇒ The principle of virtual work can be applied to elastic system by considering the virtual work of

internal forces only

external forces only

internal as well as external forces

none of the above

⇒ The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in

vertical direction

horizontal direction

inclined direction

the direction in which the deflection is required

⇒ Effects of shear force and axial force on plastic moment capacity of a structure are respectively to

increase and decrease

increase and increase

decrease and increase

decrease and decrease

⇒ The timber floor not spanning on the masonry wall but properly anchored to the wall gives

lateral restraint but not rotational restraint

rotational restraint but not lateral restraint

both lateral and rotational restraints

neither lateral nor rotational restraint

⇒ Number of unknown internal forces in each member of a rigid jointed plane frame is

1

2

3

6

⇒ For strengthening a 50 m long and 5 m high straight compound wall built in brick work, which one of the following would be most suitable?

providing buttresses at certain intervals

providing a deeper foundation

using a richer mortar

using stronger bricks