Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust |

A. | is increased [Wrong Answer] |

B. | is decreased [Wrong Answer] |

C. | remains unchanged [Correct Answer] |

D. | becomes zero [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :Rishiraj Bharadwaj Said on 2021-07-15 03:20:30B. decreased !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by

shear

vertical tensile splitting

buckling

any of the above

⇒ Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than

10 cm

15 cm

20 cm

30 cm

⇒ The three moments equation is applicable only when

the beam is prismatic

there is no settlement of supports

there is no discontinuity such as hinges within the span

the spans are equal

⇒ If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to

0 6

0.75

0.85

0.95

⇒ The moment distribution method in structural analysis can be treated as

Force method

Displacement method

Flexibility method

None of these

⇒ The number of independent displacement components at each joint of a rigid-jointed space frame is

1

2

3

6

⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is

unstable

stable and statically determinate

stable and statically indeterminate

none of the above

⇒ The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in

vertical direction

horizontal direction

inclined direction

the direction in which the deflection is required

⇒ The number of independent equations to be satisfied for static equilibrium of a plane structure is

1

2

3

6

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ The carryover factor in a prismatic member whose far end is fixed is

0

1/2

3/4

1

⇒ Weaker mortar. Of these statements

2 and 3 are correct

1 and 2 are correct

1 and 3 are correct

1, 2 and 3 are correct

⇒ In moment distribution method, the sum of distribution factors of all the members meeting at any joint is always

zero

less than 1

1

greater than 1

⇒ In column analogy method, the area of an analogous column for a fixed beam of span L and flexural rigidity El is taken as

L/EI

L/2EI

L/3EI

L/4EI

⇒ The ratio between the stress produced in a bar by a sudden applicaiton of load on compared to the stress produced by the gradual application of same load is

1.5

2.0

2.5

3.0

⇒ Which of the following methods of structural analysis is a displacement method ?

moment distribution method

column analogy method

three moment equation

none of the above

⇒ Direct load carrying capacity of a brick masonry wall standing freely as against when it supports RC slab will be

more

less

the same in both the cases

100%

⇒ The width of the analogous column in the method of column analogy is

2/EI

1/EI

1/2 EI

1/4 EI

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of

1.2

1.4

1.6

2.0

⇒ When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would

change from compression to tension

change from tension to compression

always be compression

always be tension

⇒ Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is

2

3

6

8

⇒ Number of unknown internal forces in each member of a rigid jointed plane frame is

1

2

3

6

⇒ For masonry work with solid bricks, consistency of mortar should be

5 to 8 cm

9 to 13 cm

14 to 18 cm

19 to 23 cm

⇒ When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that

the head of the load reaches the section

the tail of the load reaches the section

the load position should be such that the section divides it equally on both sides

the load position should be such that the section divides the load in the same ratio as it divides the span

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?

5 mm

0.5 mm

0.05 mm

0.005mm

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than

Vt x height of shorter opening

Vt x height of longer opening

Ax height of shorter opening

Vi x height of longer opening

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as

sum of thickness of both leaves

two-third of the sum of thickness of both the leaves

actual thickness of the stronger leaf

larger of (b) and (c)

⇒ Unequal settlements in the supports of a statically indeterminate structure develop

Member forces

Reactions from supports

No reactions

Strains in some members only

⇒ Maxwell's reciprocal theorem in structural analysis can be applied in

All elastic structures

Plastic structures

Symmetrical structures only

Prismatic element structures only

⇒ To generate the j th column of the flexibility matrix

a unit force is applied at coordinate j and the displacements are calculated at all coordinates

a unit displacement is applied at co-ordinate j and the forces are calculated at all coordinates

a unit force is applied at coordinate j and the forces are calculated at all coordinates

a unit displacement is applied at co-ordinate j and the displacements are calculated at all co-ordinates