Question is ⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is, Options are ⇒ (A) unstable, (B) stable and statically determinate, (C) stable and statically indeterminate, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is, Options are ⇒ (A) unstable, (B) stable and statically determinate, (C) stable and statically indeterminate, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is
A.	unstable [Correct Answer]
B.	stable and statically determinate [Wrong Answer]
C.	stable and statically indeterminate [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 31 -4 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following methods of structural analysis is a displacement method ?
moment distribution method
column analogy method
three moment equation
none of the above

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by
shear
vertical tensile splitting
buckling
any of the above

⇒ Castigliano's first theorem is applicable
for statically determinate structures only
when the system behaves elastically
only when principle of superposition is valid
none of the above

⇒ The method of virtual work in the analysis of structures results is
Compatible deformations
Equilibrium of forces
Stress strain relations
None of these

⇒ When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would
change from compression to tension
change from tension to compression
always be compression
always be tension

⇒ Which of the following is not the displacement method ?
Equilibrium method
Column analogy method
Moment distribution method
Kani's method

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ The moment distribution method in structural analysis can be treated as
Force method
Displacement method
Flexibility method
None of these

⇒ In column analogy method, the area of an analogous column for a fixed beam of span L and flexural rigidity El is taken as
L/EI
L/2EI
L/3EI
L/4EI

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ For masonry work with solid bricks, consistency of mortar should be
5 to 8 cm
9 to 13 cm
14 to 18 cm
19 to 23 cm

⇒ The fixed support in real beam becomes in the conjugate beam is
Fixed support
Hinged support
Roller support
Free support

⇒ Which of the following will give higher ratio of brickwork strength to mortar strength ?
1 : % : 3
1 : Vz: 4>/2
1:1:6
1:2:9

⇒ Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have
high shrinkage
less strength
both (a) and (b)
none of above

⇒ The three moment equation in structural analysis is basically a
Stiffness method
Displacement method
Energy method
Flexibility method

⇒ The force method in structural analysis always ensures
Equilibrium
Kinematically admissible t'orces
Equilibrium of forces
None of the above

⇒ Minimum compressive strength in N/mm2 for H1 type mortar used for masonry is
3
5
7.5
10

⇒ Number of unknown internal forces in each member of a rigid jointed plane frame is
1
2
3
6

⇒ The stiffness method in structural analysis is also known as
Unit load method
Consistent deformation method
Force method
Displacement method

⇒ In the displacement method of structural analysis, the basic unknowns are
displacements
force
displacements and forces
none of the above

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder
always occurs at center of span
always occurs under a wheel load
never occurs under a wheel load
none of the above

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by
m + r + 2j
m - r + 2j
m + r - 2j
m + r - 3j

⇒ Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than
10 cm
15 cm
20 cm
30 cm

⇒ In moment distribution method the sum of distribution factors of all the members meeting at any joint is always
Zero
< 1
> 1
= 1

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by
2j - r
j - 2r
3j - r
2j + r

⇒ Water retentivity for brick masonry should not be less than
50%
60%
70%
80%

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of
1.2
1.4
1.6
2.0

⇒ Effects of shear force and axial force on plastic moment capacity of a structure are respectively to
increase and decrease
increase and increase
decrease and increase
decrease and decrease

⇒ The carryover factor in a prismatic member whose far end is fixed is
0
1/2
3/4
1