Question is ⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies, Options are ⇒ (A) less than the left half span, (B) whole of left half span, (C) more than the left half span, (D) whole span, (E) , Leave your comments or Download question paper.

Question is ⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies, Options are ⇒ (A) less than the left half span, (B) whole of left half span, (C) more than the left half span, (D) whole span, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies
A.	less than the left half span [Wrong Answer]
B.	whole of left half span [Wrong Answer]
C.	more than the left half span [Wrong Answer]
D.	whole span [Correct Answer]
View Answer 25 -3 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The timber floor not spanning on the masonry wall but properly anchored to the wall gives
lateral restraint but not rotational restraint
rotational restraint but not lateral restraint
both lateral and rotational restraints
neither lateral nor rotational restraint

⇒ The analysis of statically indeterminate structures by the unit load method is based on
Consistent deformation
Stiffness method
Consistent force
None of these

⇒ Weaker mortar. Of these statements
2 and 3 are correct
1 and 2 are correct
1 and 3 are correct
1, 2 and 3 are correct

⇒ The three moments equation is applicable only when
the beam is prismatic
there is no settlement of supports
there is no discontinuity such as hinges within the span
the spans are equal

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of
0.4 kg/cm2
0.7 kg/cm2
1.0 kg/cm2
1.2 kg/cm2

⇒ The number of independent equations to be satisfied for static equilibrium in a space structure is
2
3
4
6

⇒ A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be
8 kN.m
15 kN.m
30 kN.m
60 kN.m

⇒ If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to
0 6
0.75
0.85
0.95

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ Unequal settlements in the supports of a statically indeterminate structure develop
Member forces
Reactions from supports
No reactions
Strains in some members only

⇒ The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in
vertical direction
horizontal direction
inclined direction
the direction in which the deflection is required

⇒ The fixed support in a real beam becomes in the conjugate beam a
roller support
hinged support
fixed support
free end

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as
sum of thickness of both leaves
two-third of the sum of thickness of both the leaves
actual thickness of the stronger leaf
larger of (b) and (c)

⇒ The carryover factor in a prismatic member whose far end is fixed is
0
1/2
3/4
1

⇒ Which of the following is not the displacement method ?
Equilibrium method
Column analogy method
Moment distribution method
Kani's method

⇒ Direct load carrying capacity of a brick masonry wall standing freely as against when it supports RC slab will be
more
less
the same in both the cases
100%

⇒ The thickness of each leaf of a cavity wall shall not be less than
5 cm
7.5 cm
10 cm
15 cm

⇒ Which of the following methods of structural analysis is a force method ?
slope deflection method
column analogy method
moment distribution method
none of the above

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is
0.15 MPa
0.125 MPa
0.1 MPa
0.075 MPa

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of
1.2
1.4
1.6
2.0

⇒ The fixed support in real beam becomes in the conjugate beam is
Fixed support
Hinged support
Roller support
Free support

⇒ Principle of superposition is applicable when
deflections are linear functions of applied forces
material obeys Hooke's law
the action of applied forces will be affected by small deformations of the structure
none of the above

⇒ Number of unknown internal forces in each member of a rigid jointed plane frame is
1
2
3
6

⇒ Independent displacement components at each joint of a rigid-jointed plane frame are
three linear movements
two linear movements and one rotation
one linear movement and two rotations
three rotations

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than
Vt x height of shorter opening
Vt x height of longer opening
Ax height of shorter opening
Vi x height of longer opening

⇒ Minimum compressive strength in N/mm2 for H1 type mortar used for masonry is
3
5
7.5
10

⇒ The stiffness method in structural analysis is also known as
Unit load method
Consistent deformation method
Force method
Displacement method

⇒ The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to
R
R²
1/R
1/R²

⇒ In plastic analysis the shape factor for a circular section is
1.5
1.6
1.7
1.75

⇒ Water retentivity for brick masonry should not be less than
50%
60%
70%
80%