Question is ⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?, Options are ⇒ (A) 5 mm, (B) 0.5 mm, (C) 0.05 mm, (D) 0.005mm, (E) , Leave your comments or Download question paper.

Question is ⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?, Options are ⇒ (A) 5 mm, (B) 0.5 mm, (C) 0.05 mm, (D) 0.005mm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
A.	5 mm [Correct Answer]
B.	0.5 mm [Wrong Answer]
C.	0.05 mm [Wrong Answer]
D.	0.005mm [Wrong Answer]
View Answer 31 -16 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The number of independent displacement components at each joint of a rigid-jointed space frame is
1
2
3
6

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is
0.16 Wl
0.20 Wl
0.24 Wl
0.25 Wl

⇒ A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear height between RCC slabs at top and bottom. The slenderness ratio of the wall is
15
19
20
25

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is
0.15 MPa
0.125 MPa
0.1 MPa
0.075 MPa

⇒ For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is
0.211 L
0.25 L
0.234 L
0.5 L

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder
always occurs at center of span
always occurs under a wheel load
never occurs under a wheel load
none of the above

⇒ The moment distribution method in structural analysis can be treated as
Force method
Displacement method
Flexibility method
None of these

⇒ The fixed support in a real beam becomes in the conjugate beam a
roller support
hinged support
fixed support
free end

⇒ The torsional stiffness of a member can be defined as
Torque for unit moment
Torque for unit twist
Moment for unit twist
Torsion for unit twist

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as
sum of thickness of both leaves
two-third of the sum of thickness of both the leaves
actual thickness of the stronger leaf
larger of (b) and (c)

⇒ Which of the following methods of structural analysis is a force method ?
slope deflection method
column analogy method
moment distribution method
none of the above

⇒ The three moments equation is applicable only when
the beam is prismatic
there is no settlement of supports
there is no discontinuity such as hinges within the span
the spans are equal

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by
shear
vertical tensile splitting
buckling
any of the above

⇒ The moment area theorems in the structural analysis fall in the category of
Force method
Displacement method
Stiffness method
Iterative method

⇒ The Castigliano's second theorem can be used to compute deflections
in statically determinate structures only
for any type of structure
at the point under the load only
for beams and frames only

⇒ The thickness of each leaf of a cavity wall shall not be less than
5 cm
7.5 cm
10 cm
15 cm

⇒ When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that
the head of the load reaches the section
the tail of the load reaches the section
the load position should be such that the section divides it equally on both sides
the load position should be such that the section divides the load in the same ratio as it divides the span

⇒ The stiffness method in structural analysis is also known as
Unit load method
Consistent deformation method
Force method
Displacement method

⇒ Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than
10 cm
15 cm
20 cm
30 cm

⇒ Which of the following will give higher ratio of brickwork strength to mortar strength ?
1 : % : 3
1 : Vz: 4>/2
1:1:6
1:2:9

⇒ Bending moment at any section in a conjugate beam gives in the actual beam
slope
curvature
deflection
bending moment

⇒ While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of
zero length
infinite length
zero moment of inertia
none of the above

⇒ In moment distribution method the sum of distribution factors of all the members meeting at any joint is always
Zero
< 1
> 1
= 1

⇒ Maxwell's reciprocal theorem in structural analysis can be applied in
All elastic structures
Plastic structures
Symmetrical structures only
Prismatic element structures only

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by
m + r + 2j
m - r + 2j
m + r - 2j
m + r - 3j

⇒ In column analogy method, the area of an analogous column for a fixed beam of span L and flexural rigidity El is taken as
L/EI
L/2EI
L/3EI
L/4EI

⇒ The truss can be analysed by the methods of joints when the number of unknown at a joint is equal to
1
2
3
4