Question is ⇒ The carryover factor in a prismatic member whose far end is fixed is, Options are ⇒ (A) 0, (B) 1/2, (C) 3/4, (D) 1, (E) , Leave your comments or Download question paper.

Question is ⇒ The carryover factor in a prismatic member whose far end is fixed is, Options are ⇒ (A) 0, (B) 1/2, (C) 3/4, (D) 1, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The carryover factor in a prismatic member whose far end is fixed is
A.	0 [Wrong Answer]
B.	1/2 [Correct Answer]
C.	3/4 [Wrong Answer]
D.	1 [Wrong Answer]
View Answer 45 -26 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Water retentivity for brick masonry should not be less than
50%
60%
70%
80%

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ For masonry work with solid bricks, consistency of mortar should be
5 to 8 cm
9 to 13 cm
14 to 18 cm
19 to 23 cm

⇒ Minimum compressive strength in N/mm2 for H1 type mortar used for masonry is
3
5
7.5
10

⇒ Principle of superposition is applicable when
deflections are linear functions of applied forces
material obeys Hooke's law
the action of applied forces will be affected by small deformations of the structure
none of the above

⇒ Which of the following will give higher ratio of brickwork strength to mortar strength ?
1 : % : 3
1 : Vz: 4>/2
1:1:6
1:2:9

⇒ When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would
change from compression to tension
change from tension to compression
always be compression
always be tension

⇒ Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have
high shrinkage
less strength
both (a) and (b)
none of above

⇒ The number of independent displacement components at each joint of a rigid-jointed space frame is
1
2
3
6

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder
always occurs at center of span
always occurs under a wheel load
never occurs under a wheel load
none of the above

⇒ When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that
the head of the load reaches the section
the tail of the load reaches the section
the load position should be such that the section divides it equally on both sides
the load position should be such that the section divides the load in the same ratio as it divides the span

⇒ The principle of virtual work can be applied to elastic system by considering the virtual work of
internal forces only
external forces only
internal as well as external forces
none of the above

⇒ Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is
2
3
6
8

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than
Vt x height of shorter opening
Vt x height of longer opening
Ax height of shorter opening
Vi x height of longer opening

⇒ Maxwell's reciprocal theorem in structural analysis can be applied in
All elastic structures
Plastic structures
Symmetrical structures only
Prismatic element structures only

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of
0.4 kg/cm2
0.7 kg/cm2
1.0 kg/cm2
1.2 kg/cm2

⇒ For strengthening a 50 m long and 5 m high straight compound wall built in brick work, which one of the following would be most suitable?
providing buttresses at certain intervals
providing a deeper foundation
using a richer mortar
using stronger bricks

⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies
less than the left half span
whole of left half span
more than the left half span
whole span

⇒ If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to
0 6
0.75
0.85
0.95

⇒ Select the correct statement
Flexibility matrix is a square symmetrical matrix
Stiffness matrix is a square symmetrical matrix
both (a) and (b)
none of the above

⇒ Which of the following methods of structural analysis is a displacement method ?
moment distribution method
column analogy method
three moment equation
none of the above

⇒ Independent displacement components at each joint of a rigid-jointed plane frame are
three linear movements
two linear movements and one rotation
one linear movement and two rotations
three rotations

⇒ The method of moment distribution in structural analysis is
An iterative method
An exact method
An approximate method
None of these

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by
2j - r
j - 2r
3j - r
2j + r

⇒ The analysis of statically indeterminate structures by the unit load method is based on
Consistent deformation
Stiffness method
Consistent force
None of these

⇒ The width of the analogous column in the method of column analogy is
2/EI
1/EI
1/2 EI
1/4 EI

⇒ The fixed support in real beam becomes in the conjugate beam is
Fixed support
Hinged support
Roller support
Free support

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is
0.16 Wl
0.20 Wl
0.24 Wl
0.25 Wl

⇒ While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of
zero length
infinite length
zero moment of inertia
none of the above

⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is
unstable
stable and statically determinate
stable and statically indeterminate
none of the above