Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Degree of kinematic indeterminacy of a pin-jointed plane frame is given by |

A. | 2j - r [Correct Answer] |

B. | j - 2r [Wrong Answer] |

C. | 3j - r [Wrong Answer] |

D. | 2j + r [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of

zero length

infinite length

zero moment of inertia

none of the above

⇒ The moment distribution method in structural analysis can be treated as

Force method

Displacement method

Flexibility method

None of these

⇒ Which of the following will give higher ratio of brickwork strength to mortar strength ?

1 : % : 3

1 : Vz: 4>/2

1:1:6

1:2:9

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ Water retentivity for brick masonry should not be less than

50%

60%

70%

80%

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is

0.15 MPa

0.125 MPa

0.1 MPa

0.075 MPa

⇒ To generate the j th column of the flexibility matrix

a unit force is applied at coordinate j and the displacements are calculated at all coordinates

a unit displacement is applied at co-ordinate j and the forces are calculated at all coordinates

a unit force is applied at coordinate j and the forces are calculated at all coordinates

a unit displacement is applied at co-ordinate j and the displacements are calculated at all co-ordinates

⇒ The number of independent equations to be satisfied for static equilibrium in a space structure is

2

3

4

6

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by

shear

vertical tensile splitting

buckling

any of the above

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder

always occurs at center of span

always occurs under a wheel load

never occurs under a wheel load

none of the above

⇒ The method of moment distribution in structural analysis is

An iterative method

An exact method

An approximate method

None of these

⇒ The number of independent equations to be satisfied for static equilibrium of a plane structure is

1

2

3

6

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by

2j - r

j - 2r

3j - r

2j + r

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by

m + r + 2j

m - r + 2j

m + r - 2j

m + r - 3j

⇒ Which of the following is not the displacement method ?

Equilibrium method

Column analogy method

Moment distribution method

Kani's method

⇒ If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to

0 6

0.75

0.85

0.95

⇒ The three moments equation is applicable only when

the beam is prismatic

there is no settlement of supports

there is no discontinuity such as hinges within the span

the spans are equal

⇒ The truss can be analysed by the methods of joints when the number of unknown at a joint is equal to

1

2

3

4

⇒ The ratio between the stress produced in a bar by a sudden applicaiton of load on compared to the stress produced by the gradual application of same load is

1.5

2.0

2.5

3.0

⇒ The Castigliano's second theorem can be used to compute deflections

in statically determinate structures only

for any type of structure

at the point under the load only

for beams and frames only

⇒ In moment distribution method, the sum of distribution factors of all the members meeting at any joint is always

zero

less than 1

1

greater than 1

⇒ The deformation of a spring produced by a unit load is called

stiffness

flexibility

influence coefficient

unit strain

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of

1.2

1.4

1.6

2.0

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than

Vt x height of shorter opening

Vt x height of longer opening

Ax height of shorter opening

Vi x height of longer opening

⇒ Bending moment at any section in a conjugate beam gives in the actual beam

slope

curvature

deflection

bending moment

⇒ In plastic analysis the shape factor for a circular section is

1.5

1.6

1.7

1.75

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of

0.4 kg/cm2

0.7 kg/cm2

1.0 kg/cm2

1.2 kg/cm2

⇒ Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have

high shrinkage

less strength

both (a) and (b)

none of above

⇒ The method of virtual work in the analysis of structures results is

Compatible deformations

Equilibrium of forces

Stress strain relations

None of these

⇒ For masonry work with solid bricks, consistency of mortar should be

5 to 8 cm

9 to 13 cm

14 to 18 cm

19 to 23 cm