Question is ⇒ The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to, Options are ⇒ (A) R, (B) R2, (C) 1/R, (D) 1/R2, (E) , Leave your comments or Download question paper.

Question is ⇒ The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to, Options are ⇒ (A) R, (B) R2, (C) 1/R, (D) 1/R2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to
A.	R [Wrong Answer]
B.	R² [Wrong Answer]
C.	1/R [Wrong Answer]
D.	1/R² [Correct Answer]
View Answer 47 -22 Explanation:- Answer : D Discuss it below : Just you Said on 2019-09-27 23:15:40 How !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The moment distribution method in structural analysis can be treated as
Force method
Displacement method
Flexibility method
None of these

⇒ Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than
10 cm
15 cm
20 cm
30 cm

⇒ The fixed support in real beam becomes in the conjugate beam is
Fixed support
Hinged support
Roller support
Free support

⇒ Weaker mortar. Of these statements
2 and 3 are correct
1 and 2 are correct
1 and 3 are correct
1, 2 and 3 are correct

⇒ When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that
the head of the load reaches the section
the tail of the load reaches the section
the load position should be such that the section divides it equally on both sides
the load position should be such that the section divides the load in the same ratio as it divides the span

⇒ While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of
zero length
infinite length
zero moment of inertia
none of the above

⇒ Water retentivity for brick masonry should not be less than
50%
60%
70%
80%

⇒ The principle of virtual work can be applied to elastic system by considering the virtual work of
internal forces only
external forces only
internal as well as external forces
none of the above

⇒ Which of the following methods of structural analysis is a displacement method ?
moment distribution method
column analogy method
three moment equation
none of the above

⇒ The fixed support in a real beam becomes in the conjugate beam a
roller support
hinged support
fixed support
free end

⇒ The method of virtual work in the analysis of structures results is
Compatible deformations
Equilibrium of forces
Stress strain relations
None of these

⇒ The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to
R
R²
1/R
1/R²

⇒ Effects of shear force and axial force on plastic moment capacity of a structure are respectively to
increase and decrease
increase and increase
decrease and increase
decrease and decrease

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by
shear
vertical tensile splitting
buckling
any of the above

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is
0.15 MPa
0.125 MPa
0.1 MPa
0.075 MPa

⇒ The number of independent displacement components at each joint of a rigid-jointed space frame is
1
2
3
6

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is
0.16 Wl
0.20 Wl
0.24 Wl
0.25 Wl

⇒ The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in
vertical direction
horizontal direction
inclined direction
the direction in which the deflection is required

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of
0.4 kg/cm2
0.7 kg/cm2
1.0 kg/cm2
1.2 kg/cm2

⇒ The moment area theorems in the structural analysis fall in the category of
Force method
Displacement method
Stiffness method
Iterative method

⇒ In the displacement method of structural analysis, the basic unknowns are
displacements
force
displacements and forces
none of the above

⇒ A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be
8 kN.m
15 kN.m
30 kN.m
60 kN.m

⇒ The thickness of each leaf of a cavity wall shall not be less than
5 cm
7.5 cm
10 cm
15 cm

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than
Vt x height of shorter opening
Vt x height of longer opening
Ax height of shorter opening
Vi x height of longer opening

⇒ In plastic analysis the shape factor for a circular section is
1.5
1.6
1.7
1.75

⇒ For masonry work with solid bricks, consistency of mortar should be
5 to 8 cm
9 to 13 cm
14 to 18 cm
19 to 23 cm

⇒ The deformation of a spring produced by a unit load is called
stiffness
flexibility
influence coefficient
unit strain

⇒ The method of moment distribution in structural analysis is
An iterative method
An exact method
An approximate method
None of these

⇒ The number of independent equations to be satisfied for static equilibrium of a plane structure is
1
2
3
6