Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | In which of the transformer is the secondary nearly short circuited under normal operating conditions? |

A. | CT [Correct Answer] |

B. | PT [Wrong Answer] |

C. | Distribution transformer [Wrong Answer] |

D. | Power transformer [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The main application of enhancement mode MOSFET is in

amplifier circuits

oscillator circuits

switching circuits

all of the above

⇒ In the circuit, V

_{s}= 10 cos ω

*t*, power drawn by the 4Ω resistor is 8 watt. The power facto

1

0.5

0.85

0

⇒ In a biased limiter the clipping level can be adjusted by adjusting the voltage of battery.

TRUE

FALSE

⇒ The dimensions of force are

MLT

^{-2}

ML

^{-1}T

^{-2}

MLT

^{-1}

ML

^{2}T

^{-2}

⇒ Which of the following is wrong for a magic used to tee?

E and H arms are decoupled

coplanar arms are coupled

all ports are perfectly matched

A signal into coplanar arm splits equally between E and H arms

⇒ The noise generated by a resistor depends upon

its resistance value

its operating temperature

both its resistance value and operating temperature

none of the above

⇒ A uniform plane EM wave incident normally on a plane surface of a dielectric material is reflected with a VSWR of 3. What percentage of incident power that is reflected?

0.1

0.25

0.5

0.75

⇒ A 750 A circuit uses thyristor of current rating 175 A. If derating is 25%, the number of thyristors in parallel is

3

4

6

10

⇒ As the frequency increases, the absorption of ground wave by earth's surface

decreases

increases

remains the same

either (a) or (c)

⇒ An RLC series circuit has Q = 100 and ω

_{0}= 20 rad/sec. The bandwidth is

0.2 rad/sec

2 rad/sec

20 rad/sec

2000 rad/sec

⇒ In figure, V

_{EB}= 0.6 V, β = 99. Then V

_{C}and I

_{C}

9.3 V and 1.98 mA respectively

4.6 V and 1.98 mA respectively

9.3 V and 0.02 mA respectively

4.6 V and 0.02 mA respectively

⇒ For an accurate clock period in 8085 it is preferable to use

Crystal

Crystal or LC resonant circuit

Crystal or RC circuit

LC or RC circuit

⇒ A counter has a modulus of 10. The number of flip flops is

10

5

4

3

⇒ The K-map for a Boolean function is shown in figure. The number of essential prime implicants for this functio

4

5

6

8

⇒ A quiescent state of a transistor implies

zero bias

no output

no distortion

no input signal

⇒ If F(

*j*ω) is the Fourier transform of

*f*(

*t*), then

£

*f*(-

*t*) = F(

*j*ω)

£

*f*(-

*t*) = F* (

*j*ω)

£

*f*(-

*t*) = F(-

*j*ω)

£

*f*(-

*t*) = F* (

*- j*ω)

⇒ Typical switching time for ECL is

5 nano seconds

5 micro seconds

5 milli seconds

5 seconds

⇒ The range of RTD using platinum is about

-100° C to 700°C

-200°C to 1000°C

100°C to 1000°C

about 500°C

⇒ The bandwidth required for amplitude modulation is

half the frequency of modulating signal

equal to the frequency of modulating signal

twice the frequency of modulating signal

four times the frequency of modulating signal

⇒ In figure, S is closed at

*t*= 0. At

*t*=

*t*

_{1}, I = 1 A and

*di*/

*dt*= 1 A/s. Then the value of

1 H

2 H

3 H

4 H

⇒ The number of branches of root locus plot is equal to

the number of roots of characteristic equation

double the number of roots of characteristic equation

the number of roots of characteristic equation minus one

the number of roots of characteristic equation plus one

⇒ For stable network, the real part of poles and zeros of driving point function must be

negative

negative or zero

zero

positive

⇒ A universal RLC bridge uses

Maxwell bridge for measurement of inductance and De Sauty's bridge for measurement of capacitance

Maxwell's bridge for measurement of inductance and modified De Sauty bridge for measurement of capacitance

Maxwell Wien bridge for measurement of inductance and modified De Sauty bridge for measurement of inductance

Maxwell Wien bridge for measurement of inductance and Wien bridge for measurement of capacitance

⇒ A variable reluctance type tachometer has 150 teeth on rotor. The counter records 13500 pulse/sec. The rotational speed is

4800 RPM

5400 RPM

6000 RPM

7200 RPM

⇒ The addition of impurity in extrinsic semiconductor is about 1 part in 10

^{8}parts.

TRUE

FALSE

⇒ In a dynamometer 3 phase power factor meter, the planes of the two moving coils are at

60°

0°

120°

90°

⇒ In a circular waveguide with radius

*r*, the dominant mode is

TM

_{01}

TE

_{01}

TM

_{11}

TE

_{11}

⇒ In 8085, TRAP is

always maskable

cannot interrupt a service subroutine

used for catastrophic events like temporary power failure

lowest priority interrupt

⇒ How many JK flip-flops are needed to make a 4-bit shift register?

2

4

6

8

⇒ Which of the following be true for a CE transistor amplifier if the emitter resistor value is made equal to zero?

- Its gain will increase
- Its stability will increase
- Its gain will decrease
- Its stability will decrease

1 and 2

2 and 3

3 and 4

1 and 4