Question is ⇒ A series RLC circuit has a resonant frequency of 2000 Hz. The maximum voltage across C is likely to occur at a frequency of about, Options are ⇒ (A) 1000 Hz, (B) 4000 Hz, (C) 2025 Hz, (D) 1975 Hz, (E) , Leave your comments or Download question paper.

Question is ⇒ A series RLC circuit has a resonant frequency of 2000 Hz. The maximum voltage across C is likely to occur at a frequency of about, Options are ⇒ (A) 1000 Hz, (B) 4000 Hz, (C) 2025 Hz, (D) 1975 Hz, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A series RLC circuit has a resonant frequency of 2000 Hz. The maximum voltage across C is likely to occur at a frequency of about
A.	1000 Hz [Wrong Answer]
B.	4000 Hz [Wrong Answer]
C.	2025 Hz [Correct Answer]
D.	1975 Hz [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The time constant of a series R-C circuit is given by
R/C
RC²
RC
R²C

⇒ In an Anderson bridge the unknown inductance is measured in terms of
known inductance and resistance
known inductance
known capacitance and resistance
known capacitance

⇒ A uniform plane wave travelling in air is incident on the plane boundary between air and another dielectric medium with ε_r = 4. The reflection coefficient for the normal incidence is
zero
0.5 ∠180°
0.33 ∠0°
0.33 ∠180°

⇒ Which mode has the minimum cutoff frequency in rectangular wave guides?
TE₁₁
TE₁₀
TE₀₁
TE₂₀

⇒ An antenna has a gain of 44 dB. Assuming that the main beam of the antenna is circular in cross-section the beamwidth will be
0.4456°
1.4456°
2.4456°
3.4456°

⇒ Consider the following applications

Switch
Attenuator
Phase shifter
Oscillator

In which of the above can a PIN diode be used?
1 2 3 and 4
1 2 and 3 only
1 and 2 only
2, 3 and 4 only

⇒ One limitation of constant k filters is that Z₀ is not constant in the pass band.
TRUE
FALSE

⇒ In a positive edge triggered JK flip flop, J = 1, K = 0 and clock pulse is rising Q will
be 0
be 1
show no change
toggle

⇒ A doped semi-conductor is called
impure semi-conductor
dipole semi-conductor
bipolar semi-conductor
extrinsic semi-conductor

⇒ Integral error compensation changes a second order system to
first order system
third order system
fourth order system
either (a) or (b) depending on the system

⇒ Decimal 45.15 when converted into 9's complement will become
54.84
45.48
48.54
45.84

⇒ Barkhausen criterion of oscillation is
Aβ > 1
Aβ = 1
Aβ = < 1
Aβ ≤ 1

⇒ Which of the following is the fastest switching device?
JFET
BJT
MOSFET
Triode

⇒ A single mode fibre not suffer from which type of dispersion?
Waveguide dispersion
Material dispersion
Intermodal dispersion
Polarization mode dispersion

⇒ An ideal current source has
infinite source resistance
zero source resistance
large value of source resistance
finite value of source resistance

⇒ The hexadecimal number 5 F is equal to binary number
1010011
1011001
1010101
1011111

⇒ For the infix expression (A/B) * (C * F + (A - D) * E) the corresponding Post fix notation is
A / D * CF AD - F * +
AB / CF * AD - E * + *
AB / C * FAD - E * + *
None of the above

⇒ Inputs A and B of the given figure are applied to a NAND gate. The output is
from 0 to 6
from 0 to 2
from 0 to 1 and 2 to 3
from 1 to 2 and 3 to 4

⇒

Assertion (A): The small signal analysis of a transistor amplifier is done to obtain the current gain, voltage gain and the conversion efficiency of an amplifier.

Reason (R): The small signal analysis of a transistor amplifier uses the small signal parameters of the transistor.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ The decimal equivalent of the hexadecimal number E 5 is
279
229
327
0

⇒ In a 3 input NOR gate, the number of states in which output is 1 equals
1
2
3
4

⇒ The circuit in figure will act as ideal current source with respect to terminals A and B when frequenc
0
1 rad/sec
4 rad/sec
16 rad/sec

⇒ The maximum current and voltage ratings for a 0.5 W, 10 kW resistor are
7.07 mA and 70.7 V
70.7 mA and 70.7 V
0.707 mA and 70.7 V
7.07 mA and 70.7 x 10³ V

⇒ In low power factor wattmeter, the compensating coil is connected
in series with current coil
in parallel with current coil
in series with pressure coil
in parallel with pressure coil

⇒ The forms of IF statements in FORTRAN 77 are called
logical IF and Block IF
logical IF, block IF and arithmetic IF
logic IF, block IF, arithmetic IF and negate IF
logical IF and arithmetic IF

⇒ An intrinsic silicon sample has 2 million free electrons. The number of holes in the sample is
2 million
almost zero
more than 2 million
less than 2 million

⇒ The essential condition for antenna array to be linear is that
individual antennas of the array must be of equal size
individual antennas of the array must be equally spaced along a straight line
any two individual antennas of the array must not be in the same direction
none of the above

⇒ For a photoconductor with equal electron and hole mobilities and perfect ohmic contacts at the ends, an increase in illumination results in
a change in O.C. voltage
a change in S.C. current
a decrease in resistance
an increase in resistance

⇒ The colour coding of a resistors shows 100 K, ± 10%. When the resistance was measured with an ohmmeter, it read
95 K
80 K
120 K
85 K

⇒ A bipolar differential amplifier uses a transistor having β₀ = 200, I_CQ = 100 mA, |A_dm| = 500 and CMRR = 80 dB. The value of R_c and R_E will be respectively __________ .
1.25 kΩ, 1.25 MΩ
125 kΩ, 1.25 MΩ
1.25 MΩ, 1.25 kΩ
3.25 kΩ, 3.25 MΩ