Question is ⇒ Typical switching time for ECL is, Options are ⇒ (A) 5 nano seconds, (B) 5 micro seconds, (C) 5 milli seconds, (D) 5 seconds, (E) , Leave your comments or Download question paper.

Question is ⇒ Typical switching time for ECL is, Options are ⇒ (A) 5 nano seconds, (B) 5 micro seconds, (C) 5 milli seconds, (D) 5 seconds, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Typical switching time for ECL is
A.	5 nano seconds [Correct Answer]
B.	5 micro seconds [Wrong Answer]
C.	5 milli seconds [Wrong Answer]
D.	5 seconds [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The distance of poles from origin depends on
undamped natural frequency
damping ratio
both (a) and (b)
neither (a) nor (b)

⇒ A sinusoidal signal is measured by CRO. The scale is set at 4 mV/cm. If vertical distance between positive and negative peaks is 6 cm, the peak value of ac signal is
6 mV
12 mV
24 mV
3 mV

⇒ The skin depth at 1000 MHz as compared to that at 500 MHz is
2
12
0.707
0.5

⇒ Which of the following is active transducer?
Photoelectric
Photovoltaic
Photoconductive
Photoemissive

⇒ Consider the signal S(t) shown bel
8
12
16
18

⇒ For the circuit, let us assume that R = 1 Ω, L = 10^-3 H, and V(t) = 10 cos (1000t + 30°)V and the differential equation for I(t) is give
7.07 cos (1000t + 15°) A
70.7 cos (1000t - 30°) A
7.07 cos (1000t - 15°) A
7.07 cos (1000t + 15°) A

⇒ Transfer function of a linear system is 200 e^-j10ω The system is a
distortionless Attenuator
amplifier with Phase distortion
distortionless Amplifier
attenuator with Phase distortion

⇒ The material used for the magnet of moving coil cone type loudspeaker is
steel alloy
soft iron
hard steel
Alnico

⇒ The current flow in a semiconductor is due to
holes
electrons
holes and electrons
holes, electrons and ions

⇒ If B_max is the maximum flux density, hysteresis loss is proportional to
B_max
B^1.6_max
B²_max
B³_max

⇒ In 8085 microprocessor, what is the length of Data Buffer Register?
6 bits
8 bits
12 bits
16 bits

⇒ When R and C are connected in parallel, phase angle of Y is positive.
TRUE
FALSE

⇒ In FM and AM the ratio of signal to noise ratio at the detector output least depends upon
bandwidth
transmission
carrier frequency
modulating frequency

⇒ In what condition does BJT act like an open switch
cut off
saturation
active
both (b) and (c)

⇒

Assertion (A): Fourier series can also be written in exponential form.

Reason (R): sin (n ωt) and cos (n ωt) can be expressed as sum or difference of exponentials.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In which of the following does a negative resistance region exist in the v-i characteristics?
PIN diode
Schottky diode
Tunnel diode
Zener diode

⇒ Consider the following DO statement in Fortran 77 1
10
3
4

⇒ 300 to 3000 MHz frequency is categorized as
MF
HF
UHF
SHF

⇒ Consider the following advantages of phase array radar

simple circuitry
ability to track and scan simultaneously
ability to track many targets together
very fast scanning

Which of the above are correct?
1, 2, 3
1, 3, 4
2, 3, 4
1, 4 only

⇒ A land line telemetry system is suitable for distance upto
about 1 km only
about 10 km only
about 100 km only
any of the above

⇒ Value of 'K' for the system for which the system is stab
K < 1
K > 1
K < 2
K > 2

⇒ In figure the approximate voltage
base and emitter are - 8 V and - 7.3 V
base and collector are - 8 V and - 5 V
collector and emitter are - 5 V and - 7.3 V
base, emitter and collector are - 8, - 7.3 and - 5 V

⇒ The multivibrator circuit that has a typical application of converting sinusoidal input into a square wave output is
emitter coupled binary
Schmitt trigger
monoshot multivibrator
free-running multivibrator

⇒

Match the following:

	List I		List II
A.	Direct addressing	1.	MOV A, M
B.	Register addressing	2.	MOV C, A
C.	Register indirect addressing	3.	LDA 7
D.	Immediate addressing	4.	STA FFC

A-1, B-2, C-3, D-4
A-4, B-2, C-1, D-3
A-2, B-3, C-4, D-1
A-3, B-2, C-1, D-4

⇒ In digital circuits Schottky transistors are preferred over normal transistors because of their
lower propagation delay
lower power dissipation
higher propagation delay
higher power dissipation

⇒ For K map of the given figure the simplified Boolean expressio
Y = A B C + A B C + A B C
Y = A C + B
Y = A B C + ABC
Y = A B C + AB C + ABC

⇒ Consider the following:

Distortion
Gain
Bias stabilization
Sensitivity
Frequency response

Which of these properties of the power amplifier one should concentrate upon while designing a good power amplifier circuit?
1, 2 and 3
1, 3 and 5
2, 3 and 4
4 and 5

⇒ Which of the following is a valid FORTRAN assignment statement?
10 = N
X + 2.1 = 5.6
A = B
A = B = 1

⇒ The characteristic polynomial of a system is q(s) = 2s⁵ + s⁴ + 4s³ + 2s² + 1. The system is :
stable
marginally stable
unstable
oscillatory

⇒ An op-amp integrating circuit uses
an inductor
a capacitor
both inductor and capacitor
none of the above