Question is ⇒ Which of the following semiconductor has the highest melting point?, Options are ⇒ (A) Germanium, (B) Silicon, (C) Gallium arsenide, (D) Lead sulphide, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following semiconductor has the highest melting point?, Options are ⇒ (A) Germanium, (B) Silicon, (C) Gallium arsenide, (D) Lead sulphide, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following semiconductor has the highest melting point?
A.	Germanium [Wrong Answer]
B.	Silicon [Wrong Answer]
C.	Gallium arsenide [Wrong Answer]
D.	Lead sulphide [Correct Answer]
View Answer 1 -3 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The coil of a moving coil meter has 100 turns, is 40 mm long and 30 mm wide. The control torque is 240 x 10^-6 N-m on full scale. If B = 1 Wb/m², range of meter is
1 mA
2 mA
3 mA
4 mA

⇒ In an RC series circuit R = 100 Ω and X_C = 10 Ω. In this circuit
the current and voltage are in phase
the current leads the voltage by about 6°
the current leads the voltage by about 84°
the current lags the voltage by about 6°

⇒ A source of angular frequency 1 rad sec has a source impedance consisting of 1 Ω resistance in series with 1 H inductance. The load that will obtained the maximum power transfer is
1 Ω resistance
1 Ω resistance in parallel with 1 H inductance
1 Ω resistance in series with 1 F capacitor
1 Ω resistance in parallel with 1 F capacitor

⇒ A high pulse repetition frequency in a radar
increases the maximum range
decreases the maximum range
has no effect on the maximum range
either (a) or (b) depending on other factors

⇒ If a signal g(t) has energy E, then the energy of the signal g(2t) is equal to ...
E/2
E/4
E
2E

⇒ A 5000 W signal is attenuated by - 196 dB. The resultant signal strength is
1.26 x 10⁶ W
1.26 x 10^-2 W
1.26 x 10^-8 W
1.26 x 10^-16 W

⇒

Assertion (A): A high density IC has more diodes, transistors and resistors per unit surface area.

Reason (R): A high density IC can handle high voltages.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In the basic series inverter circuit, the source current has
low harmonic content
high harmonic content
low or high harmonic content depending on firing angle
zero harmonic content

⇒ The emitter coupled pair of BJT's gives a linear transfer relation between the differential output voltage and the differential input voltage V_id only when the magnitude of V_id is less a times the thermal voltage, where a is
4
3
2
1

⇒

Assertion (A): Thevenin's theorem and Norton's theorem are dual of each other.

Reason (R): Voltage source can be converted into current source and vice versa.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ The function shown in figure, can represent a probability density function for A _______
A = 1/4
A = 1/6
A = 1/9
A = 1/2

⇒ The reverse saturation current in a semiconductor diode consists of
avalanche current
zener current
minority carrier current
minority carrier current and surface leakage current

⇒ The advantages of high density IC are
more circuits on chip
high operating speed
low power consumption
both (a) and (b)

⇒ A capacitor is considered to be completely charged in __________ time constant.
one
three
five
eight

⇒

Match the following:

	List I (I/P - O/P relation)		List II (Property of the system)
A.	y(n) = x(n)	1.	Nonlinear, non-causal
B.	y(n) = x(n²)	2.	Linear, non casual
C.	y(n) = x²(-n)	3.	Linear causal
D.	y(n) = x²(n)	4.	Nonlinear causal

A-1, B-4, C-3, D-2
A-3, B-2, C-1, D-4
A-1, B-2, C-3, D-4
A-3, B-4, C-1, D-2

⇒ A phasor is
a line representing the magnitude and direction of an alternating quantity
a line which represents the magnitude and phase of an alternating quantity
an instrument used for measuring phases of an unbalanced 3-phase load
a coloured tag or band for distinguishing between different phases of a 3-phase supply

⇒ An RLC series circuit is excited by a step voltage E. The circuit current at t = 0 is
E/R
E/LC
zero
infinity

⇒ In a 4 bit weighted resistor D/A converter, the resistor value corresponding to LSB is 32 kΩ. The resistor value corresponding to MSB will be
32 KΩ
16 KΩ
8 KΩ
4 KΩ

⇒ The circuit of the given figure gives the output YAB
A + B
A B
A + B

⇒
Match the following:
List I List II
A. FM 1. slope-overload
B. DM 2. μ law
C. PSK 3. Envelope detector
D. PCM 4. Capture effect
5. Hilbert transform
6. Matched filter.

A-5, B-1, C-6, D-4
A-4, B-6, C-1, D-5
A-4, B-1, C-6, D-2
A-6, B-3, C-4, D-2

⇒ In the analysis of common emitter amplifier we may neglect
h_re
h_oe
h_fe
h_ie

⇒ In the signal flow graph in the given figure the number of forward paths and pairs of non-touching loops are respecti
3 and 1
3 and 2
4 and 2
2 and 4

⇒
Assertion (A): The unit of telephone traffic measurement is erlang.
Reason (R): International circuits for communication are fitted with echo suppressors.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒
Assertion (A): Maxwell bridge is for measuring inductance of medium magnitude.
Reason (R): In Maxwell's bridge the unknown inductance is measured by comparing it with a capacitance.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ For an m x n matrix A, the eigen values are the roots of the characteristic equation
|I - A|
|λI - A| = 0
|λA - I| = 0
|A - I| = 0

⇒ The h parameter h₁₁ is the same in CE and CC circuit.
TRUE
FALSE

⇒ In a PCM system, if we increase the quantization levels from 2 to 8, how do the relative bandwidth requirements vary?
Get doubled
Get tripled
Remains same
Become eight times

⇒ Initially the number decimal 8 is stored. If instruction RAL is executed twice, the final number stored will be
decimals 8
decimal 16
decimal 32
decimal 2

⇒ Which of the following is non-saturating?
TTL
CMOS
ECL
Both (a) and (b)

⇒ In figure the coordinates of Q point on the load line are (Neglect V_{BEI_C = 10 mA, V_CE = 15 V
I_C = 5 mA, V_CE = 22.5 V
I_C = 5 mA, V_CE = 15 V
I_C = 10 mA, V_CE = 22.5 V}

	List I		List II
A.	FM	1.	slope-overload
B.	DM	2.	μ law
C.	PSK	3.	Envelope detector
D.	PCM	4.	Capture effect
		5.	Hilbert transform
		6.	Matched filter.

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math