Question is ⇒ Which addressing mode is suitable only for these instructions in which there is only one operand?, Options are ⇒ (A) Implicit, (B) Register, (C) Direct, (D) Immediate, (E) , Leave your comments or Download question paper.

Question is ⇒ Which addressing mode is suitable only for these instructions in which there is only one operand?, Options are ⇒ (A) Implicit, (B) Register, (C) Direct, (D) Immediate, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which addressing mode is suitable only for these instructions in which there is only one operand?
A.	Implicit [Correct Answer]
B.	Register [Wrong Answer]
C.	Direct [Wrong Answer]
D.	Immediate [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Find the value of K and velocity constant K_v so that the maximum overshoot in the unit step response is 0.2 and the peak time is 1
12.37, 0.175
12.86, 2.175
11.36, 1.175
1.86, 0.175

⇒ According to Barkhausen criteria in order to sustain the oscillations
loop gain of the circuit must be negligible
loop gain of the circuit must be equal to unity
the phase shift around the circuit must be 180°
none of the above

⇒ The use of thermocouple meters for ac measurement leads to a scale which is
linear
square law
logarithmic
exponential

⇒ 8085 data bus has 8 lines and is bidirectional.
TRUE
FALSE

⇒ For a BJT, under the saturation condition,
I_C = βI_B
I_C = aI_B
I_C is independent of all other parameters
I_C < βI_B

⇒ Consider a silicon p-n junction at room temperature having the following paramet
is 0.70V
is 0.76V
is 0.82V
cannot be estimated from the data given

⇒ The P-type substrate in a conventional pn Junction isolated integrated circuits should be connected to
any where
a dc ground potential
the most positive potential available in the circuit
the most negative potential available in the circuit

⇒

Assertion (A): At a temperature of 1000 K, thermionic emission current is about 0.1 A/cm² of surface.

Reason (R): Thermionic emission current is given by I_th = SA₀ T² e^-Ew/kT.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ The filter circuit for feeding a wooffer has
an inductance in series and capacitance in parallel
a capacitance in series and an inductance in parallel
a resistance in series and an inductance in parallel
an inductance in series and a resistance in parallel

⇒ Which of the following be true for a CE transistor amplifier if the emitter resistor value is made equal to zero?

Its gain will increase
Its stability will increase
Its gain will decrease
Its stability will decrease

Select the correct answer from the codes given below
1 and 2
2 and 3
3 and 4
1 and 4

⇒ A resistor is rated at 0.75 watt, 1 kΩ. Its current rating is
1 mA
27.386 mA
1.268 mA
5.393 mA

⇒ Large scale integration refers to
more than 50 gates on the same chip
more than 80 gates on the same chip
more than 100 gates on the same chip
none of the above

⇒ In an optional fiber the refractive index of cladding material should be
nearly 1
very low
less than that of core
more than that of core

⇒ As compared to a full wave diode rectifier circuit using centre tapped transformer, the bridge diode rectifier circuit has the main advantage of
higher current carrying capacity
higher efficiency
lower ripple factor
lower PIV

⇒ For iron, the ferromagnetic Curie temperature is
about 20 K
about 100°C
about -20°C
about 1000 K

⇒ The V_s is give
8 V
13 V
1 V
4 V

⇒ A planar array radar uses a high gain planar array antenna.
TRUE
FALSE

⇒ A P-N junction diode dynamic conductance is directly proportional to
the applied voltage
the temperature
its current
thermal voltage

⇒ In figure, the reading of wattmeter will be proportio
V I cos θ
3 VI cos θ
3 VI sin θ
V I sin θ

⇒ Four capacitors are in parallel. Their values are 36.3 μF, 3.85 μF, 34.002 μF and 850 μF with an uncertainty of digit in the last place. The total capacitance in significant figures is
75.0 μF
75.0 ± 0.1 μF
75.1 ± 0.1 μF
75.002 ± 0.1 μF

⇒ The dimension of flux density is
MT^-1Q^-1
MT^-2
MT¹Q¹
MT^-1Q^-2

⇒ The charges between a hollow and solid metal spheres reside
through out in both
on outer surface in hollow and through out in solid
on the outer surface in both
none of the above

⇒ The bandwidth required for amplitude modulation is
half the frequency of modulating signal
equal to the frequency of modulating signal
twice the frequency of modulating signal
four times the frequency of modulating signal

⇒ TTL logic is preferred to DRL logic because
greater fan-out is possible
greater logic levels are possible
greater fan-in is possible
less power consumption is achieve

⇒ The system with given pole-zero diagram is _______
Causal
Anti-causal
Both sided
Cannot be determined

⇒ Which one of the following devices is not used as the controller in a stabilizer?
DIAC
TRIAC
SCR
Power transistor

⇒ e^-3^t is a
energy signal
power signal
Both (a) and (b)
none

⇒ If memory chip size is 256 x 1 bits, the number of chips required to make 1 k byte memory is
8
12
24
32

⇒ The gain of a current element is
0 dB
1.67 dB
1.76 dB
3 dB

⇒ UJT can be used for
firing an SCR
turning off an SCR
both firing and turning off an SCR
none of the above