Question is ⇒ The zeros of a minimum phase function lie on, Options are ⇒ (A) imaginary axis, (B) left half plane or origin, (C) left half plane or imaginary axis, (D) right half plane or origin, (E) , Leave your comments or Download question paper.

Question is ⇒ The zeros of a minimum phase function lie on, Options are ⇒ (A) imaginary axis, (B) left half plane or origin, (C) left half plane or imaginary axis, (D) right half plane or origin, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The zeros of a minimum phase function lie on
A.	imaginary axis [Wrong Answer]
B.	left half plane or origin [Wrong Answer]
C.	left half plane or imaginary axis [Correct Answer]
D.	right half plane or origin [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The order of the differential equa
1
2
3
4

⇒ Consider the following statements regarding an antenna:

It is a transducer
Its performance is essentially frequency sensitive
It is a reciprocal device
With increase in its effective aperture area, width of the radiated beam increases.

Which of the above statements are correct?
1, 2 and 3
1, 2 and 4
2 and 3 only
1 and 4 only

⇒ The most commonly used magnetron is
cylindrical
parallel plate
inclined plate
flat plate

⇒ If an additional two diodes were used to connect the 1 kW load across a bridge rectifier circuits, utilizing the full secondary of the transformer, how much d.c. power could be delivered using a transformer with the rating of 105 VA?
35 W
60 W
85 W
100 W

⇒ What happens when a paramagnetic material is heated above Curie temperature?
It becomes diamagnetic
It becomes nonmagnetic
It becomes ferromagnetic
It becomes anti-ferromagnetic

⇒ High speed logic circuits use
pulses with very small width
pulses with very large width
pulses whose width is neither small nor large
either (b) or (c)

⇒ If a signal band limited for f_m is sampled at a rate less than 2 f_m the reconstructed signal will be
smaller in amplitude
distorted
having higher frequencies suppressed
none of the above

⇒ When reverse bias is applied to a junction diode
minority carrier current is increased
majority carrier current is increased
potential barrier is lowered
potential barrier is raised

⇒ In orthogonal BFSK. the energy of information bearing term is :
the same as total transmitted energy
one half of total transmitted energy
one fourth of total transmitted energy
None

⇒ If a and b are the width and height of rectangular wave-guide the cut off wavelength λ_c for TE₂₀ mode is equal to
a
a + b
a - b
a² + b²

⇒ An 8085 microprocessor based system uses a 4 k x 8 bit RAM whose address in AAOOH. The address of the last byte in this RAM is
OFFFH
1000H
B9FFH
BA00H

⇒ The maximum effective aperture of an antenna which is operating at wavelength of 2 m and has directivity of 100 is
15.92
31.84
2.18
3.184

⇒ If J, I and a denote current density, current and area of cross section of a conductor, then
J = Ia
J = I/a²
J = I/a
J = Ia²

⇒ Consider the signal S(t) shown bel
8
12
16
18

⇒ Whenever a wave is incident on a perfect conductor then the reflection coefficient is
1
0
1 < 180°
depend upon η₁, η₂

⇒ A digital watch contains
quartz crystal oscillator
RC oscillator
LC oscillator
either quartz or RC oscillator

⇒ Which of the following are universal gates?

NAND
NOR
XOR

Select the correct answer from the codes given below:
1 and 2 only
1 and 3 only
2 and 3 only
1, 2 and 3

⇒ Low frequency boost can be easily compensated by
attenuating the frequencies from 0 to 1.25 MHz
using an appropriate de-emphasis circuit in the receiver
using an appropriate pre-emphasis circuit in the transmitter
none

⇒ A chopper cannot be line commutated.
TRUE
FALSE

⇒ Effective address is calculated by adding or subtracting displacement value to
immediate address
Relative address
absolute address
base address

⇒ State transition table and state transition diagram form part of design steps for
combinational circuits
sequential circuits
delay circuits
all of the above

⇒ The terms RMS and average values apply only to sine waves.
TRUE
FALSE

⇒ Which of the following is a valid integer constant?
127
127
127
125 + 3

⇒ In the circuit of fi
V_a would always lag V_b
V_a would always lead V_b
V_a and V_b can be in phase
phase angle between V_a and V_b would always be 90°

⇒ Binary number 1101.101 is equivalent to decimal number?
13.5
13.75
13.625
13.875

⇒ If V_dc1 is the dc output voltage in half wave controlled rectifier circuit feeding resistive load and V_dc2 is the dc output voltage in full wave controlled rectifier circuit (M - 2 connection) feeding resistive load, then
V_dc1 = 0.5 V_dc2 for all values of firing angle
V_dc1 = V_dc2 for all values of firing angle
V_dc1 ≤ 0.5 V_dc2 for all values of firing angle
V_dc1 ≥ 0.5 V_dc2 for all values of firing angle

⇒

Assertion (A): When p-n junction is forward biased, steady current flows.

Reason (R): When a p-n junction is forward biased, free electrons cross the junction from n to p and holes from p to n.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ A varactor diode is used for
tuning
rectification
amplification
rectification and amplification

⇒ If ω₀ is the angular frequency of rotation of electron in the absence of magnetic field, the angular frequency ω, when a magnetic field B is acting is ω ≅ ω₀ + (e/2m)B.
TRUE
FALSE

⇒ If input frequency is 50 Hz, the frequency of output wave in a half wave diode rectifier circuit is
25 Hz
50 Hz
100 Hz
200 Hz