Question is ⇒ For a series circuit of variable R and X<sub>L</sub>, the impedance locus is, Options are ⇒ (A) a straight line parallel to X axis in first quadrant, (B) a straight line parallel to X axis in fourth quadrant, (C) a straight line parallel to Y axis in second quadrant, (D) a straight line parallel to Y axis in first quadrant, (E) , Leave your comments or Download question paper.

Question is ⇒ For a series circuit of variable R and X<sub>L</sub>, the impedance locus is, Options are ⇒ (A) a straight line parallel to X axis in first quadrant, (B) a straight line parallel to X axis in fourth quadrant, (C) a straight line parallel to Y axis in second quadrant, (D) a straight line parallel to Y axis in first quadrant, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For a series circuit of variable R and X_L, the impedance locus is
A.	a straight line parallel to X axis in first quadrant [Correct Answer]
B.	a straight line parallel to X axis in fourth quadrant [Wrong Answer]
C.	a straight line parallel to Y axis in second quadrant [Wrong Answer]
D.	a straight line parallel to Y axis in first quadrant [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Figure shows the terminals of a transistor in plastic package TO 18. T
terminals 1, 2, 3 are emitter, collector, base respectively
terminals 1, 2, 3 are emitter, base, collector respectively
terminals 1, 2, 3 are base, emitter collector, respectively
terminals 1, 2, 3 are collector, emitter, base respectively

⇒

Assertion (A): Light triggering is very suitable for HVDC transmission.

Reason (R): Light triggering has the advantage of complete electrical isolation of gate circuit.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒

Assertion (A): Each memory chip has its own address latch.

Reason (R): ALE signal comes out of microprocessor 8085 and goes to memory chip.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒

Assertion (A): In series R-L-C circuit, the current may lead or lag the voltage depending on the value of R.

Reason (R): Phase angle of an R-L series circuit is tan^-1 (ωL/R).

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒

Match the following:

	List I (Modulation )		List II (Modulation Index)
A.	DSBFC	1.	μ > 1
B.	DSBSC	2.	μ > 0
C.	SSB	3.	∞
		4.	μ, any value

A-2, B-2, C-3
A-1, B-3, C-3
A-4, B-2, C-1
A-2, B-3, C-1

⇒ The colour code on a carbon resistor is yellow-violet-orange. The value of resistance is
17000 Ω
27000 Ω
37000 Ω
47000 Ω

⇒ What is the minimum value of VSWR that may exist on a transmission line?
Less than zero
Zero
One
10

⇒ A uniform wave have components
in the perpendicular direction E existing while H is zero
in the direction of propagation E existing while H is zero
E and H are zero in direction perpendicular to direction of propagation
E and H existing only in direction perpendicular to direction of propagation

⇒ An inverting amplifier has R₁ = 10 kΩ, and R_f = 150 kΩ then the O/P voltage, if input voltage V_i = 1 volt.
-15 V
-10 V
15 V
-14 V

⇒ RMS value is always higher than average value.
TRUE
FALSE

⇒ In a tape recorder
the width of air gaps of record and erase heads is almost equal
the air gap of record head is wider than the air gap of erase head
the air gap of erase head is wider than the air gap of record head
any of the two air gaps can be wider than the other

⇒ The input to negative clamper has a peak value of V_p. Then in the output the positive and negative peaks are nearly
0 and -2 V respectively
V_p and -V_p respectively
2 V_p and 0 respectively
none of the above

⇒ For a junction FET in the pinch off region as the drain voltage is increased, the drain current
becomes zero
abruptly decreases
abruptly increases
remains constant

⇒ While selecting a memory chip the feature which should be examined is
capacity
ac characteristics
dc characteristics
all of the above

⇒ In figure, R = 20KΩ and C = 75 pF. The converter clock frequency wil
606 Hz
1212 Hz
555 KHz
606 KHz

⇒ T-flip-flop is commonly used as
a delay switch
a digital counter only
a digital counter and frequency divider
any of the above

⇒ The depletion layer in a reverse biased p-n junction is due to the presence of
electrons
holes
both electrons and holes
immobile ions

⇒ For the circuit shown in the figure, D has a transition from 0 to 1 after CLK changes from 1 to 0. Assume gate delays to be neglig
Q goes to 1 to the CLK transition and stays at 1
Q goes to 0 at the CLK transition and stays at 10
Q goes to 1 at the CLK transition and goes to 0 when D goes to 1
Q goes to 0 at the CLK transition and goes to 1 when D goes to 1

⇒ A rectangular waveguide, in dominant TE mode, has dimensions 10 cm x 15 cm. The cut off frequency is
10 GHz
1 GHz
15 GHz
25 GHz

⇒ A wavelength of 1 mm could be expected in
VLF
HF
EHF
SHF

⇒ In some on-off controllers a differential gap is provided
to make the manufacture process easier
to prevent too often frequent operation of controller
both (a) and (b)
neither (a) nor (b)

⇒ If the load current is high, the pressure coil of wattmeter should be connected directly across the load.
TRUE
FALSE

⇒ In band III of TV, distant reception (beyond line of sight range) is possible due to
tropospheric bending by refraction
reflection of waves
ionospheric scattering
none of the above

⇒ As applied to a flip flop the word edge triggered's means
flip flop can change state when clock transition occurs
flip flop can change state when clock signal goes from LOW to HIGH only
flip flop can change state when clock signal goes from HIGH to LOW only
none of the above

⇒ In a four element Yagi-Uda antenna
there is one driven element, one director and two reflectors
there is one driven element, two directors and one reflector
there are two driven elements, one director and two reflectors
all the 4 elements are driven element

⇒

Match the following:

	List I (Circuit)		List II (Characteristics)
A.	Darlington pair	1.	uses pnp and npn transistors used as power amplifier
B.	CB amplifier	2.	Voltage gain nearly 1 and high input impedance
C.	Cascade amplifier	3.	low input impedance used for high frequency isolation

A-1, B-2, C-3
A-2, B-3, C-1
A-2, B-1, C-3
A-3, B-1, C-2

⇒ Assuming accumulator contain A 64 and the carry is set (1). What will register A and (CY) contain after XRA A?
A 6 H, 1
A 6 H, 0
00 H, 0
00 H, 1

⇒ UJT can be used for
firing an SCR
turning off an SCR
both firing and turning off an SCR
none of the above

⇒ The decimal equivalent of binary 1101.11 is
9.75
13.75
11.5
11.75

⇒ Percentage increase in the reverse saturation current of a diode if the temperature is increased from 25°C to 50°C
0.5
5
5.657
5.756