Question is ⇒ Which is known as flash converter?, Options are ⇒ (A) Weighted resistor D/A converter, (B) Parallel A/D converter, (C) Stair step A/D converter, (D) Up-down counter type A/D converter, (E) , Leave your comments or Download question paper.

Question is ⇒ Which is known as flash converter?, Options are ⇒ (A) Weighted resistor D/A converter, (B) Parallel A/D converter, (C) Stair step A/D converter, (D) Up-down counter type A/D converter, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which is known as flash converter?
A.	Weighted resistor D/A converter [Wrong Answer]
B.	Parallel A/D converter [Correct Answer]
C.	Stair step A/D converter [Wrong Answer]
D.	Up-down counter type A/D converter [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ At room temperature, a possible value for the mobility of electrons in the inversion layer of a silicon n-channel MOSFET is
450 cm²/V-s
1350 cm²/V-s
1800 cm²/V-s
3600 cm²/V-s

⇒ Which are the pending interrupts?
5.5
6.5
7.5
None

⇒ Statement 1
Statement 1 is true but statement 2 is false
Statement 1 is false but statement 2 is true
Both the statements are true
Both the statements are false

⇒ n-channel MOS is
slower than p-channel MOS
faster than p-channel MOS
same as p-channel MOS
none of these

⇒ The figure of merit for a logic family is
gain band width product
(propagation delay time) (power dissipation)
(fan out) (power dissipation)
(noise margin) (power dissipation)

⇒ The simplest method of suppression of unwanted side band in AM is
filter method
phase shift method
third method
both (a) and (b)

⇒ In free space, line of sight propagation case, the transmission losses between transmitter and receiver increase with frequency (f) as
f
f²
f⁴
f^1/2

⇒ Consider the following statements regarding registers and latches:
Registers are made of edge-triggered FFs, whereas latches are made from level-triggered FFs.
Registers are temporary storage devices whereas latches are not.
A latch employs cross-coupled feedback connections.
A register stores a binary word whereas a latch does not.
Which of the above statements is/are correct?
1 only
1 and 3
2 and 3
3 and 4

⇒ In an FM system, when the AF is 500 Hz and the AF voltage is 2.4 V, the deviation is 4.8 kHz. If the AF voltage is now increased to 7.2 V, the new deviation will be
4.8 kHz
9.6 kHz
14.4 kHz
28.8 kHz

⇒
Assertion (A): In rectangular waveguide TE₀₁ mode is just TE₁₀ mode rotated by 90°.
Reason (R): When a rectangular waveguide is rotated by 90°, the broad and narrow dimensions get interchanged.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ An arithmetic statement in C must be
integer mode arithmetic statement
real mode arithmetic statement
mixed mode arithmetic statement
any of the above

⇒ A CMOS amplifier when compared to an N-channel. MOSFET, has the advantage of
higher cut off frequency
higher voltage gain
higher current gain
lower current drain from the power supply, there by less dissipation

⇒ A cycloconverter is
ac-dc converter
dc-ac converter
dc-dc converter
ac-ac converter

⇒
Assertion (A): In a serial in-serial out shift register, access is available only to the left most or right most flip flops
Reason (R): If the output of a shift register is feedback to serial input it can be used as a ring counter.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In figure, the switch is closed at t = 0. At t = 0⁺ The value of current supplied by batter
0.0416666666666667
0.0833333333333333
zero
infinity

⇒ The characteristic impedance of loss less transmission line is
L/R
L/C
1/LC
C/L

⇒ Which one of the following statements regarding compandor is FALSE?
It compresses the higher-amplitude parts of a signal before modulation and expands them back to normal again after demodulation.
It gives preferential treatment to the weaker parts of the signal
For weaker signals it gives a poor ratio of signal strength to quantizing error
Weaker signals, traverse more quantum steps than they would do otherwise and so quantizing error is reduced.

⇒ Using 4-bit numbers (n = 4) if k = 0011₂, how is k expressed in 2's complement?
1011₂
1101₂
1100₂
0101₂

⇒ The output of a Mealy system is 1 if there has been a pattern of 11000, otherwise 0. The minimum state for this system is :
4
5
6
7

⇒ A single phase half wave regulator uses
2 diodes and 2 thyristors
2 thyristors
1 diode and 1 thyristor
2 diodes

⇒ The theoretical maximum efficiency of a half wave diode rectifier is
0.406
0.5
0.812
slightly less than 100%

⇒
Match the following:
List I List II
A. Reflex Klystron 1. High efficiency
B. Dielectric loaded wave guide 2. Slow wave structure
C. TWT 3. Cross field device
D. Multi Cavity Klystron 4. Oscillator

A-1, B-2, C-3, D-4
A-4, B-3, C-2, D-1
A-2, B-4, C-1, D-3
A-3, B-1, C-4, D-2

⇒ For the block diagram of the given figure, the equation describing system dynamic
(1 + RCs) Δθ₀(s) = Δθ_i(s) + R Δ H(s)
(1 + RCs) [ΔH(s)] = Δθ(s) - Δθ₀(s)
(1 + RCs) Δθ₀(s) = RΔ H(s) - Δ θ_i(s)
(1 + RCs) Δθ_i(s) = Δ H(s)[R] - Δθ₀(s)

⇒ Two 2's complement number having sign bits X and Y are added and the sign bit of the result is Z. then, the occurrence of overflow is indicated by the Boolean function.
XYZ
X Y Z
X YZ + XY Z
XY + YZ + ZX

⇒ In a JK flip flop output Q_n = 1 and it does not change when clock pulse is applied. The possible combination of J_n and K_n is (X denotes don't care)
X and 0
X and 1
0 and X
1 and X

⇒ When energy is fed into open wire transmission line the energy may get dissipated due to
radiation
conductor heating
dielectric heating
all of the above

⇒ Digital technologies being used now-a-days are
DTL and EMOS
TTL, ECL, CMOS and RTL
TTL, ECL and CMOS
TTL, ECL. CMOS and DTL

⇒ For measuring current at a high frequency we should use
moving iron instrument
electrostatic instrument
thermocouple instrument
moving coil instrument

⇒ Consider the following:
A TV receiver antenna should pick up the TV signal and develop maximum voltage from the available strength of signal
It should reject unwanted signals
It should not suffer from co-channel interference
It should have a very narrowband
The correct statements are
1 and 2 only
1, 2 and 3 only
1, 2, 3, 4
2, 3 only

⇒ A bipolar differential amplifier uses a transistor having β₀ = 200, I_CQ = 100 mA, |A_dm| = 500 and CMRR = 80 dB. The value of R_c and R_E will be respectively __________ .
1.25 kΩ, 1.25 MΩ
125 kΩ, 1.25 MΩ
1.25 MΩ, 1.25 kΩ
3.25 kΩ, 3.25 MΩ

	List I		List II
A.	Reflex Klystron	1.	High efficiency
B.	Dielectric loaded wave guide	2.	Slow wave structure
C.	TWT	3.	Cross field device
D.	Multi Cavity Klystron	4.	Oscillator

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math