Question is ⇒ In a power diode the reverse recovery time is the time from the instant the forward current is zero to the instant when reverse recovery current has decayed to, Options are ⇒ (A) 50% of peak reverse current, (B) 25% of peak reverse current, (C) 10% of peak reverse current, (D) zero value, (E) , Leave your comments or Download question paper.

Question is ⇒ In a power diode the reverse recovery time is the time from the instant the forward current is zero to the instant when reverse recovery current has decayed to, Options are ⇒ (A) 50% of peak reverse current, (B) 25% of peak reverse current, (C) 10% of peak reverse current, (D) zero value, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a power diode the reverse recovery time is the time from the instant the forward current is zero to the instant when reverse recovery current has decayed to
A.	50% of peak reverse current [Correct Answer]
B.	25% of peak reverse current [Wrong Answer]
C.	10% of peak reverse current [Wrong Answer]
D.	zero value [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following is used for generating time varying wave forms?
MOSFET
PIN diode
Tunnel diode
UJT

⇒ Which of the following parameters is not specified for digital ICs?
Gate dissipation
Propagation delay
Noise margin
Bandwidth

⇒ Impedance inversion may be obtained with
a short circuited stub
a quarter wave line
an open circuited stub
a half wave line

⇒ In a positive edge triggered D flip flop
D input is called direct set
Preset is called direct reset
Present and clear are called direct set and reset respectively
D input overrides other inputs

⇒ Find the power absorbed or delivered by each sou
a = -32 b = - 12 c = -80 d = -60
a = -32 b = - 12 c = 80 d = 60
a = 32 b = 12 c = -80 d = 60
a = -32 b = 12 c = 80 d = -60

⇒ A higher directivity is specified by
high gain low BW (Beamwidth)
high gain high BW
low gain high BW
none of the above

⇒ In single tone AM modulation, the transmission efficiency for m = 1 is
0.333
0.5
1
0.1665

⇒ The number of unused states in a 4 bit Johnson counter is
2
4
8
12

⇒ Hysteresis loss in a transformer working at 220 V and at a frequency of 50 Hz is 100 W. When the transformer is operated at 220 V and at a frequency of 100 Hz, what is the hysteresis loss?
50 W
100 W
200 W
400 W

⇒ Which converters uses integrating op-amp?
Parallel A/D converter
Single slope A/D converter
Dual slope A/D converter
Both (b) and (c)

⇒

Assertion (A): Secondary instruments require calibration at frequent intervals.

Reason (R): Secondary instruments have many errors.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ The dual of A + [B + (AC)] + D is
A + [(B (A + C))] + D
A [B + AC] D
A + [B (A + C)] D
A [B (A + C)] D

⇒ What will be conversion time of a successive approximation A/D converter which uses 2 MHz clock and 5 bit binary ladder containing 8 V reference.?
2.5 μ sec
25 μ sec
3 μ sec
4 μ sec

⇒ Two rectangular waveforms of duration t₁ and t₂ seconds are convolved. What is the shape of the resulting waveform?
Triangular
Rectangular
Trapezoidal
Semi-circular

⇒ In a 4 bit full adder how many half adders and OR gates are required
8 and 4
7 and 4
7 and 3
8 and 3

⇒ If an additional two diodes were used to connect the 1 kW load across a bridge rectifier circuits, utilizing the full secondary of the transformer, how much d.c. power could be delivered using a transformer with the rating of 105 VA?
35 W
60 W
85 W
100 W

⇒ The maximum range of a transmitter depends on
its frequency
its power
both its frequency and power
none of the above

⇒ When a complex signals is used to frequency modulate a carrier, the resulting sideband distribution is
symmetrical about the carrier
not necessarily symmetrical about the carrier
decided by the predominant sidebands
none of the above

⇒ One XOR gate can work as
one bit magnitude comparator
two bit magnitude comparator
either (a) or (b)
neither (a) nor (b)

⇒ The converter whose conversion time is independent of number of bits is
dual stope
counter type
parallel conversion
successive approximation

⇒ A series RC circuit has fixed R and C and variable f. The current locus will lie in the first quadrant.
TRUE
FALSE

⇒ Magnetic amplifier is used for
voltage amplification
power amplification
current amplification
frequency amplification

⇒ If A = 629 ± 8 and B = 131 ± 3, A - B with range of doubt is
498 ± 8
498 ± 4
498 ± 11
498 ± 13

⇒ Figure shows basic Hartley oscillator configuration. Do you think the polarities marked for the split coiled are corr
yes they are
no they are not
it really doesn't matter
none of the above

⇒ The network
First order system and the pole
Second order system of the two poles are
Second order system of the poles is
none of the above

⇒ Geosynchronous satellites are always launched in the equatorial plane because it is the only plane which provides
24-hour orbit
stationary satellite
global communication
zero-gravity environs

⇒ Transverse magnetic (TM) waves have
magnetic field component H in the direction of propagation
electric field component E in the direction of propagation
magnetic field component H in the direction of propagation and no component of electric field E in this direction
electric field component E in the direction of propagation and no component of magnetic field H in this direction

⇒ In radio receivers, the value of IF is
100 kHz
225 kHz
455 kHz
850 kHz

⇒ A microwave junction is matched at all ports if the S matrix
has all diagonal elements zero
has all diagonal elements equal but not zero
has all diagonal elements complex
is Hermitian

⇒ In 8086 the instruction ADD AL, CH means
the two 8 bit values in registers AL and CH are added and result placed in register AL
the two 8 bit values in registers AL and CH are added and result placed in register CH
the two 16 bit values in registers AL and CH are added and result placed in register AL
the two 16 bit values in registers AL and CH are added and result placed in register CH