Question is ⇒ It is desired to display the digit 7 using a seven segment display. The LEDs to be turned on are, Options are ⇒ (A) a, b, c, (B) b, c, d, (C) c, d, e, (D) a, b, d, (E) , Leave your comments or Download question paper.

Question is ⇒ It is desired to display the digit 7 using a seven segment display. The LEDs to be turned on are, Options are ⇒ (A) a, b, c, (B) b, c, d, (C) c, d, e, (D) a, b, d, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	It is desired to display the digit 7 using a seven segment display. The LEDs to be turned on are
A.	a, b, c [Correct Answer]
B.	b, c, d [Wrong Answer]
C.	c, d, e [Wrong Answer]
D.	a, b, d [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The refractive index of E layer at frequency of 81 N
0
∞
1
0.5

⇒ Consider the following statement: At finite temperature, magnetic dipoles in a material are randomly oriented giving low magnetization. When magnetic field H is applied, the magnetization?

Increases with H
Decreases with H
Decreases with temp for constant H

Which of the statement given above is/are correct?
1
2
2, 3
1 and 3

⇒ In crystalline solids, atoms are stacked in a regular manner.
TRUE
FALSE

⇒ TTL logic is preferred to DRL logic because
greater fan-out is possible
greater logic levels are possible
greater fan-in is possible
less power consumption is achieve

⇒ Choose the appropriate turn on and turn off time of a FET
1 ns, 10ns
6 ns, 18ns
4 ns, 8 ns
10 ns, 10 ns

⇒ Probability of error in DPSK is less than PSK
TRUE
FALSE
equal
depend upon noise

⇒ Electrical conductivity of metals expressed in ohm^-1 m^-1 is of the order of
10¹⁰
10⁵
10^-4
10^-6

⇒ The amplifier used in bootstrap voltage sweep should have a gain of
1
+∞
-1
-∞

⇒ Each of the following statements regarding frequency modulation is true except
amplitude of the modulated wave remains the same as that of carrier wave
the amount of variation of deviation from the original carrier frequency is determined by the frequency of the modulating signal
the rate at which the frequency of modulated wave varies is determined by the frequency of the modulating signal
frequency of modulated wave increases as the signal voltage increases and vice-versa

⇒ Which of the following can not be used as a variable name in C?
else
coal
ram
vendy

⇒ Antenna efficiency of antenna is, if radiation resistance is 370 Ω and loss resistance is 100 Ω
0.8
0.87
0.78
0.2127

⇒ Which of the following is not the main characteristic of a FET?
Drain resistance
Forward transconductance
Temperature stability
Amplification factor

⇒ In an n type semiconductor the fermi level is 0.35 eV below the conduction band, the concentration of donor atoms is increased to three times. The new position of Fermi level will be
0.35 eV below conduction band
about 0.32 eV below conduction band
about 0.32 eV above conduction band
about 0.1 eV below conduction band

⇒ A transistor with a = 0.9 and I_CBO = 10 μA is biased so that I_BQ = 90 μA. Then I_EQ will be
5.15 mA
5.2 mA
5 mA
990 mA

⇒ Which of the following has unique representation of 0?
sign magnitude
1's complement
2's complement
both (b) and (c)

⇒ It has been found that in a rectifier circuit with RC filter one RC section reduces ripple by 15%. Two RC sections are used in cascade the reduction in ripple would be
0.15
0.3
1.5
2.25

⇒ For the given truth table, the correct Boolean expressio
XYZ + X YZ + X Y Z
X Y Z + XYZ + X YZ
X Y Z + XYZ + XY Z
XYZ + XYZ + XY Z

⇒ In measuring a resistance by voltmeter-ammeter method, the voltmeter can be connected either across supply or across the resistance. If the resistance is low, the voltmeters should be connected
across the supply
across the resistance
either in two positions
preferably across the supply

⇒ The output v-i characteristics of enhancement type MOSFET has
only an ohmic region
only a saturation region
an ohmic region at low voltage value and a saturation region at high voltage
a saturation region at low voltage value and an ohmic region at high voltage

⇒ An op-amp integrating circuit uses
an inductor
a capacitor
both inductor and capacitor
none of the above

⇒ The range of signed decimal number that can be represented by 6 bit in complement number is
-31 to +31
-63 to +64
-64 to +63
-32 to +31

⇒

Assertion (A): Impatt diode can be used in both amplifiers and oscillators.

Reason (R): Impatt diode has a low resistance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Conductivity is measured in terms of
mho/metre
ohm/metre
mho/metre²
ohm/metre²

⇒ A 3 phase star-connected load has one capacitor C in R phase and two equal resistances in Y and B phases.The phase sequence is RBY. Then
V_B0 > V_Y0
V_B0 < V_Y0
V_B0 = V_Y0
V_B0 = V_BY

⇒ In n channel JFET
I_D and V_DS are positive but V_GS is negative
I_D and V_GS are positive but V_DS is negative
V_DS and V_GS are positive but I_D is negative
I_D, V_DS and V_GS are all positive

⇒ Consider the following statements

The effect of feedback is to reduce system error
Feedback increases the system gain at one frequency but reduces the system gain as another frequency
Feedback can cause an originally stable system to become unstable

Which of the above statements are correct?
1, 2, 3
1, 2
2, 3
1, 3

⇒ The current through a 1 mH inductance is i(t) = 2.56 x 10^-2 - 4 x 10³ t for 2 ≤ t ≤ 20 μ sec. The voltage across the inductor is
4
8
0
8 x 10³

⇒ As compared to a bipolar transistor, a JFET is
highly sensitive to changes in input voltage
more sensitive to changes in input voltage
less sensitive to changes in input voltage
equally sensitive to changes in input voltage

⇒ What is the purpose of peak clipper circuits in radio transmitters?
To prevent overmodulation
To reduce bandwidth
To increase bandwidth
To regulate oscillator I/P voltage

⇒ For a second order system, the position of poles is shown in the given figure. This syste
undamped
overdamped
underdamped
critically damped