Question is ⇒ The value of current read by ideal ammeter A in figure is __________ amp, Options are ⇒ (A) 0, (B) 3, (C) 2.5, (D) 5, (E) , Leave your comments or Download question paper.

Question is ⇒ The value of current read by ideal ammeter A in figure is __________ amp, Options are ⇒ (A) 0, (B) 3, (C) 2.5, (D) 5, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The value of current read by ideal ammeter A in figure is __________ amp
A.	0 [Wrong Answer]
B.	3 [Wrong Answer]
C.	2.5 [Wrong Answer]
D.	5 [Correct Answer]
View Answer 2 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Consider the following statements about conditions that make a metal semiconductor contact rectifying

N type semiconductor with work function φ_s more than work function φ_M of metal
N type semiconductor with work function φ_s less than work function φ_M of metal
P type semiconductor with work function φ_s more than work function φ_M of metal
P type semiconductor with work function φ_s less than work function φ_M of metal.

Of these statements
1 and 3 are correct
2 and 3 are correct
1 and 4 are correct
2 and 4 are correct

⇒ Consider the following statements for 8085

The most significant 8 bits of address are transmitted on the 8 lines on which data is transmitted.
Eight pins are dedicated to transmit the most significant 8 bits of memory address.
The least significant 8 bits of address are transmitted on the lines on which data is transmitted.
The data and leass significant 8 bits are transmitted at different points in time.

Which of the above statements are correct?
all
1, 2 and 3 only
2, 3 and 4 only
1, 3 and 4 only

⇒ Cross-over distortion behaviour is a characteristic of
class A output stage
class B output stage
class AB output stage
common base output stage

⇒ Consider the differential amplifier shown in figure. (Assume β is very hi
5 V
10 V
15 V
30 V

⇒ The damping ratio of a pair of complex poles when expressed in terms of angle θ measured from jω axis equal to
sin θ
cos θ
tan θ
cot θ

⇒ The polar plot of P (jω) = 45° as ω varies from -∞ to ∞ is
a straight line parallel to x-axis
a straight line parallel to y-axis
a line passing through origin and inclined at 45°
a line in first quadrant passing through origin and inclined at 45° to positive x-axis

⇒ For overdamped systems a quadratic factor in transfer function can be replaced by two first order factors with real poles
TRUE
FALSE

⇒ Impedance inversion may be obtained with
a short circuited stub
a quarter wave line
an open circuited stub
a half wave line

⇒ In floating point representation, the accuracy is
10 bit
9 bit
8 bit
6 bit

⇒ It is desired to evaluate the expression F = B * COS (Y) + C * SQR (COS (Y) + A * COS (Y) * COS (Y) * COS (Y)
F = B * COS (Y) + C * SQR [COS (Y)] + A * COS (Y) * SQR [COS (Y)]
F = B * COS (Y) + C * COS(Y) * COS (Y) + A * COS (Y) * COS (Y) * COS (Y)
X = COS(Y)



⇒ A signal with ± 10 V ranged and 1 KHz band width is being digitized using a sample and hold circuit and a 10 bit quantizer. The quantization step is :
1 x 10^-9 V
5 x 10^-9 V
2.5 x 10^-9 V
0.5 x 10^-9 V

⇒ In a ripple counter,
whenever a flip flop sets to 1, the next higher FF toggles
whenever a flip flop sets to 0, the next higher FF remains unchanged
whenever a flip flop sets to 1, the next higher FF faces race condition
whenever a flip flop sets to 0, the next higher FF faces race condition

⇒ An 8 bit data is to be entered into a parallel in register. The number of clock pulses required is
8
4
2
1

⇒ Which statement is true for an ac circuit?
Active power is always less than apparent power
Active power cannot be more than apparent power
Active power is always more than reactive power
Active power cannot be more than reactive power

⇒ The gate width of a monostable multivibrator is given by
T = 1.1 RC
T = 0.693 RC
0.963 RC
T = 0.369 RC

⇒ Inverse Fourier transform of '1' is
U(t)
δ(t)
0'
infinite

⇒ The state equations are in the form
X = AX + BW
X = AX + Bu
X = AX + Bx
either (a) or (b)

⇒ The load circuit of a single phase full bridge inverter
must be underdamped
must be overdamped
may be underdamped or overdamped
may be any type of load

⇒ If the potential functions V₁ and V₂ satisfy Laplace's equation within a closed region and assume the same values on its surface, then which of the following is correct?
V₁ and V₂ are identical
V₁ is inversely proportional to V₂
V₁ has the same direction as V₂
V₁ has the same magnitude as V₂ but has different direction

⇒ Which of the following directives in 8085 causes two bytes to be reserved in the memory?
D S
D B
D W
E Q U

⇒ TTL uses
multi-emitter transistors
multi-collector transistors
multi-base transistors
multi-emitter or multi-collector transistors

⇒ For an ideal 3000 Hz channel, S/N ratio is
3
1.5
4
2

⇒ Which of the following is a vector quantity?
Standing wave ratio
Reflection coefficient
Gain
All of the above

⇒ If carrier modulated by a digital bit stream had one of the possible phases of 0°, 90°, 180°, 270°, then the modulation is called.
BPSK
QPSK
QAM
MSK

⇒ For the floating point numbers 1.81 x 10^-29 and 0.0152 x 10¹⁸ the normalised forms are
0.181 x 10^-28 and 0.152 x 10¹⁷respectively
18.1 x 10^-30 and 0.152 x 10¹⁷ respectively
0.181 x 10^-28 and 1.52 x 10¹⁶ respectively
None of the above

⇒ A volt ratio box should have low resistance.
TRUE
FALSE



⇒ The shunt admittance of a transmission line is given by
γ = R + jωL
γ = R - jωL
γ = G + jωC
γ = jωGC

⇒ An RL impedance function can also be realized as
RC impedance function
RC admittance function
LC impedance function
LC admittance function

⇒ Match the following:
 List I  List II 
A. Ratio of maximum energy stored to energy dissipated per cycle 1. Propagation constant
B. TEM mode is loss less medium 2. Cutoff frequency is zero
C. Ratio of frequency in radian to phase velocity of EM wave 3. Quality factor of cavity
D. TEM is the mode of lowest cutoff frequency 4. Cylindrical waveguide

A-3, B-2, C-4, D-1
A-2, B-3, C-1, D-4
A-3, B-2, C-1, D-4
A-2, B-3, C-4, D-1

⇒ All of the output pulses are at full transmitter power for a strong signal in all of the following except
PWM
PAM
PFM
PCM

	List I		List II
A.	Ratio of maximum energy stored to energy dissipated per cycle	1.	Propagation constant
B.	TEM mode is loss less medium	2.	Cutoff frequency is zero
C.	Ratio of frequency in radian to phase velocity of EM wave	3.	Quality factor of cavity
D.	TEM is the mode of lowest cutoff frequency	4.	Cylindrical waveguide









Users Also Read
Previous Papers
Aptitude
Reasoning
Gen.Knowledge
Speak English
English / Verbal
Online / Mock Test
Vedic Math







    
	
	




    
	StudySite.org is world's best free online study content provider, Copyright © 2024 by 
StudySite.org All Rights Reserved