Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | The amplitude modulated wave is given by __________ e = 25(1 + 0.7 cos 5000t - 0.3 cos 1000t) x sin 5 x 10^{6}t The amplitude of carrier and sideband frequencies in magnitudes are |

A. | 25, 0.7, 0.3 [Wrong Answer] |

B. | 25, 0.7, - 0.3 [Wrong Answer] |

C. | 24, 17.5, 7.5 [Wrong Answer] |

D. | 25, 8.75, 3.75 [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ In a two phase servomotor the two stator windings have a phase difference of

30°

45°

90°

135°

⇒ The device 'one shot' has

two stable states

one stable state

either 1 or 2 stable states

no stable state

⇒ When a bit is 0 is a DDR, it makes the corresponding port pin an __________ On the other hand, a 1 bit programs a __________ Pin.

output, input

output, output

input, input

input, output

⇒ For AM receivers the standard IF frequency is

106 kHz

455 kHz

1.07 MHz

10.7 MHz

⇒ A delay equalizer is a

low pass filter

band pass filter

all pass filter

high pass filter

⇒ Figure sho

JFET

*n*-channel MOSFET

*p*-channel MOSFET

none of the above

⇒ In TTL the transistors are driven into and out of saturation.

TRUE

FALSE

⇒ If the functions

*w, x, y, z*are as foll

*w = z x = z*

*w = z, x = y*

*w = y*

*w = y = z*

⇒ The channel of JFET consists of

*p*type material only

*n*type material only

conducting material

either

*p*or

*n*type material

⇒ A generator of 50 Ω internal impedance and operating at 1 GHz feeds a 75 Ω load via a coaxial line of characteristic impedance 50 Ω. The VSWR on the feed line is

0.5

1.5

2.5

1.75

⇒ Consider the following statements about conditions that make a metal semiconductor contact rectifying

- N type semiconductor with work function φ
_{s}more than work function φ_{M}of metal - N type semiconductor with work function φ
_{s}less than work function φ_{M}of metal - P type semiconductor with work function φ
_{s}more than work function φ_{M}of metal - P type semiconductor with work function φ
_{s}less than work function φ_{M}of metal.

1 and 3 are correct

2 and 3 are correct

1 and 4 are correct

2 and 4 are correct

⇒ A non-linear element has zero resistance.

TRUE

FALSE

⇒ Varactor diodes use

silicon

GaAs

either (a) or (b)

neither (a) nor (b)

⇒ The feedback resistance r

_{d}in small signal model of MOSFET is of the order of

1000 MΩ

1 MΩ

1 KΩ

100 Ω

⇒

**Assertion (A):** Gate triggering is the most commonly used method for triggering of an SCR.

**Reason (R):** Even a small gate current is sufficient to turn on an SCR.

Both A and R are correct and R is correct explanation of A

Both A and R correct but R is not correct explanation of A

A is correct but R is wrong

A is wrong but R is correct

⇒ A line is excited by a 100 V dc source. If reflection coefficients at both ends are 1 each then

there will be no oscillations on line

there will be only 1 or 2 oscillations on line

there will be a finite number of oscillations on line

the oscillations will continue indefinitely

⇒ A linear diode detector uses RC filter. As modulation index increases the maximum permissible value of time constant RC

increases

decreases

remains constant

either (a) or (c)

⇒ The self inductances of two coils are 27 H and 3 H. If the winding or coils is such that 50% of flux of one links the other, the mutual inductance is

30 H

24 H

9 H

4.5 H

⇒ Which of the following binary product is incorrect?

1100 x 1010 = 1111000

1.01 x 10.1 = 11.001

1100110 x 1000 = 1100110000

None of the above

⇒ The internal resistance of a current source used in the model of a BJT while analyzing a circuit using BJT is :

very high

very low

zero

of the order of a few mega ohms

⇒ The reactance of coupling capacitors, for DC quantities, is

zero

low

infinite

zero or low

⇒ Consider the following statements about loop antenna

- It is suitable for direction finding application
- It is a single turn or multiturn coil carrying RF current
- The loop is surrounded by a magnetic field everywhere perpendicular to the loop

1 and 2 only

1 only

1, 2, 3

2 and 3 only

⇒ Which of the following configuration has low thermal stability?

CB

CC

CE

All have identical thermal stability

⇒ For TE or TM modes of propagation in bounded media, the phase velocity is

independent of frequency

is a linear function of frequency

is a non-linear function of frequency

can be frequency dependent or frequency independent on the source

⇒ As per Hall effect, if any specimen carrying a current I is applied in a transverse magnetic field B, then an electric field E is induced in the specimen in the direction.

parallel to I

perpendicular to B and parallel to I

parallel to I and B

perpendicular to both I and B

⇒ In indicating instruments the controlling torque is provided by a spring.

TRUE

FALSE

⇒ In a bridge inverter with single pulse width modulation

the output frequency is equal to frequency of reference signal

the output frequency is equal to frequency of control signal

either (a) or (b)

neither (a) nor (b)

⇒ For a flexible cable, most suitable insulation is

magnesium oxide

glass fibre

insulating tape

polyvinyl chloride

⇒ Which of the following is a valid real constant?

-81.56

73

10254,1

42

⇒ For a second order system delay time

*t*is the time required to reach

_{d}half the final value for the very first time

the final value for the very first time

90% of the final value for the very first time

none of the above