Question is ⇒ Instruction cycle is the time required to complete the execution of an instruction., Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ Instruction cycle is the time required to complete the execution of an instruction., Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Instruction cycle is the time required to complete the execution of an instruction.
A.	TRUE [Correct Answer]
B.	FALSE [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a line with finite attenuation
power transmission is least efficient when there are no standing waves on the line
power transmission is most efficient when there are no standing waves on line
Load power depends on phase constant
standing waves will always exist on the line

⇒ Conductivity σ, mobility μ and Hall coefficient K_H are related as
μ = σK_H
σ = μK_H
K_H = μσ
K_H =(μσ)^1.1

⇒ If the diameter of a wire is doubled, the current carrying capacity of the wire becomes
half
twice
four times
one-fourth

⇒ Which of the following produces very wide drifts in clock frequency?
Crystal
RC circuit
LC resonant circuit
Crystal and RC circuit

⇒ It has been found that in a rectifier circuit with RC filter one RC section reduces ripple by 15%. Two RC sections are used in cascade the reduction in ripple would be
0.15
0.3
1.5
2.25

⇒ The storage capacity of DSDD disk and DSHD disk are
1.2 MB each
360 KB each
1.2 MB and 360 KB respectively
360 KB and 1.2 MB respectively

⇒ The distance between target and radar is reduced to half. Power received increases by
42751
42739
4 times
16 times

⇒ In the circuit shown, the steady state is reached with S open S is closed at t = 0, the current I in the 1 Ω resistor connected is to be determined at t = 0⁺ is give
1
2
3
42828

⇒ In a series RLC circuit for lower frequency power factor is ________
leading, Lagging
lagging, Leading
independent of frequency
same

⇒ For a sine wave the average value is calculated over half the cycle.
TRUE
FALSE

⇒ The following properties are associated with ferroelectric materials:

Its susceptibility is negative.

The susceptibility is expresse
1 only
1 and 3
2 only
1, 2 and 3

⇒ In Z_RC (s) has a pole at s = ∞, the last element in first Foster realization is
R
C
R and C in series
R and C in parallel

⇒ The units for electric dipole moment are
coulombs
colomb-metre
coulomb/metre
coulomb/m²

⇒ Schering bridge operates at a high voltage of about 10 kV.
TRUE
FALSE

⇒ A broadside array consisting of 200 cm wavelength with 10 half-wave dipole spacing 10 cm. And if each array element feeding with 1 amp. current and operating at same frequency then find the half power beamwidth
4°
2°
10°
15°

⇒ In figure, which value of Z_L will cause maximum power to be transferred to the l
2 + j2 Ω
2 - j2 Ω
- 2 Ω
2 Ω

⇒ The access time of a word in 4 MB main memory is 100 ms. The access time of a word in a 32 kb data cache memory is 10 ns. The average data cache bit ratio is 0.95. The efficiency of memory access time is
9.5 ns
14.5 ns
20 ns
95 ns

⇒
Assertion (A): Hall effect is used to find the type of semiconductor.
Reason (R): When a specimen of semiconductor carrying current I lies in a magnetic field the force on electrons and holes is in opposite directions.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a telephone system, the grade of service means
the quality of sound reception at the receiver telephone
the probability that a called for connection is established
the type of wires cables used for the system
none of the above

⇒ The feedback control system shown in figure is sta
for all K ≥ 0
only if K ≥ 1
only if 0 ≤ K < 1
only if -1 ≤ K < 1

⇒ For edge triggering in flip flops, manufacturers use
RC circuit
direct coupled design
either RC circuit or direct coupled design
none of the above

⇒ A mod-2 counter followed by a mod 5 is same as
mod-7 counter
A decade counter
mod-3 counter
none

⇒ The use of SSB
halves the bandwidth required for transmission
does not affect the bandwidth for transmission
decreases the bandwidth required for transmission by 25%
decreases the bandwidth required for transmission by 66.6%

⇒ Average latency time of magnetic tape memory is of the order of
1 μ sec
1 msec
1 sec
1 minute

⇒ If E_b, the energy per bit of a binary digital signal is 10^-6 watt sec. and the one sided power spectral density of the white noise N₀ = 10^-5 W/Hz, then the output SNR of the matched filter is
26 dB
10 dB
20 dB
13 dB

⇒ The dead zone in a pyrometer is 0.125% of span. The calibration is 400°C to 1000°C. What temperature change might occur before it is detected.
0.125°C
0.75°C
0.4°C
1°C

⇒ The characteristics of which device has peak point and valley point
SCR
PUT
SCS
Shockley diode

⇒ Which of the following is a valid real constant in FORTRAN 77?
1.2 E 231
3 E - 2
-3.2 E 2.3
1.2 E 23

⇒ The high voltage level of a digital signal in positive logic is
1
0
either 1 or 0
-1
⇒ For the signal flow graph of the given figure consider the following statements
1. It has three forward paths
2. It has three individual loops
3. It has two non touching loops
Out of above the correct statements
1, 2, 3
1, 2
2, 3
1, 3