Question is ⇒ The constellation diagram of a modem has four states as shown in the figure given below. What is the bit rate of this mod, Options are ⇒ (A) Two times its band rate, (B) Four times its band rate, (C) Same as band rate, (D) Sufficient information is not given to give the answer, (E) , Leave your comments or Download question paper.

Question is ⇒ The constellation diagram of a modem has four states as shown in the figure given below. What is the bit rate of this mod, Options are ⇒ (A) Two times its band rate, (B) Four times its band rate, (C) Same as band rate, (D) Sufficient information is not given to give the answer, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The constellation diagram of a modem has four states as shown in the figure given below. What is the bit rate of this mod
A.	Two times its band rate [Correct Answer]
B.	Four times its band rate [Wrong Answer]
C.	Same as band rate [Wrong Answer]
D.	Sufficient information is not given to give the answer [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): Maxwell bridge is for measuring inductance of medium magnitude.

Reason (R): In Maxwell's bridge the unknown inductance is measured by comparing it with a capacitance.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ In 8086
the registers SI and DI are used for string operation
the registers CS and DS are used for string operation
the registers SS and ES are used for string operation
the registers SI and SP are used for string operation

⇒ The specific gravity of tungsten is 13.8 and its atomic weight is 184.0 Assume that there are two free elements per atom. Then the Fermi level or characteristic energy for the crystal in eV will be
8.95 eV
-8.95 eV
7.326 eV
-7.326 eV

⇒ The characteristic equation of flip-flop gives the next state Q_{N + 1} in terms of present state Q_N and the inputs. Which one of the following is the characteristic equation of J - K flip-flop?
Q_N+1 = JQ_N + KQ_N
Q_N+1 = J + KQ_N
Q_N+1 = KQ_N + JQ_N
Q_N+1 = K + JQ_N

⇒ Debye temperature of metals is
about 10 K
about 200 K
about 600 K
about 2 K

⇒ A short vertical grounded antenna is required to radiate at 1 MHz. The effective height of the antenna is 302 m. The calculated value of radiation resistance is
1.58 Ω
158 Ω
15.8 Ω
none

⇒ As applied to a flip flop the word edge triggered's means
flip flop can change state when clock transition occurs
flip flop can change state when clock signal goes from LOW to HIGH only
flip flop can change state when clock signal goes from HIGH to LOW only
none of the above

⇒ VLF waves are used for communication system because
of low power requirement
they are least prone to distortion
they penetrate the ionosphere easily
the transmitting antennas are of convenient size

⇒

Assertion (A): Bolometer is frequently used in microwave power measurement.

Reason (R): In a bolometer the input microwave power causes a change in resistance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ In a broadcast superheterodynes receiver having no RF amplifier, the loaded Q of the antenna coupling circuit is 100. If the intermediate frequency is 455 kHz. The image frequency at 1000 kHz will be
1010 kHz
1455 kHz
1910 kHz
545 kHz

⇒ The requirements of carrier frequency are
precise frequency value
low frequency drift
both (a) and (b)
neither (a) nor (b)

⇒ In Pulse Code Modulation system
large bandwidth is required
quantising noise can be overcome by companding
quantising noise can be reduced by decreasing the number of standard levels
suffers from the disadvantage of its incompatibly with TDM

⇒ Consider the draw backs

Slope overload
Serration noise
Granular noise

Which of these draw backs does Delta modulation have?
1 and 2 only
2 and 3 only
1 and 3 only
1, 2, 3

⇒ For the two port of figure, z_{2226/7 Ω
6/7 Ω
2/3 Ω
1 Ω}

⇒ Instruction cycle is the time required to complete the execution of an instruction.
TRUE
FALSE

⇒ A rectangular pulse train s(t) is shown in figure is convolved with the signal cos²(4p x 10³t). The convolved signal will
DC
12 kHZ sinusoidal
8 kHZ sinusoidal
14 kHZ sinusoidal

⇒ In a bipolar transistor
recombination in base regions of both n-p-n and p-n-p transistor is low
recombination in base regions of both n-p-n and p-n-p transistors is high
recombination in base region of n-p-n transistor is low but that in p-n-p transistor is high
recombination in base region of p-n-p transistor is low but that in n-p-n transistor is high

⇒

Assertion (A): Synchronous counter has higher speed of operation than ripple counter

Reason (R): Synchronous counter uses high speed flip flops.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ A machine cycle has one clock cycle.
TRUE
FALSE

⇒ Four terminal approach is used in measuring low resistance because it
eliminates thermoelectric energy
eliminates stray capacitance
eliminates stray inductance
eliminates the effect of leads and contacts

⇒ In a JK master slave flip flop
master is clocked when clock is low
slave is clocked when clock is high
master is clocked when clock is high and slave is clocked when clock is low
master is clocked when clock is low and slave is clocked when clock is high

⇒ In a single-stage RC coupled common emitter amplifier, the phase shift at the lower 3 dB frequency is
zero
135°
180°
225°

⇒ Which of the following devices has the 'negative resistance' characteristic?
Reflex klystron
Gunn diode
P-N-P transistor
Magnetron

⇒ A single phase full converter gives maximum and minimum output voltage at firing angles of
0 and 180° respectively
180° and 0° respectively
0 and 90° respectively
90° and 0° respectively

⇒ In the circuit of figure the voltage across C at t = 0^{+0 V
20 V
very large
7.5 V}

⇒ Distances near the skip distance should be used for sky-wave propagation
to avoid the Faraday effect
to avoid tilting
to prevent sky-wave and upper ray interference
so as to exceed the critical frequency

⇒ AGC voltage is applied to the stages which are
before the detector stage
after the detector stage
either before or after the detector stage
none of the above

⇒ In figure I_D = 4 mA. Then V_{S20 V
4.4 V
0.4 V
0.44 V}

⇒ Transit time is considered as significant at
HF
MF
LF
all of the above

⇒ Analysis of EM wave in waveguide based on
circuit theory
field theory
optical theory
both (a) and (b)