Question is ⇒ An RC impadence function has a pole at <i>s</i> = 0. The first element in the Foster form of synthesis, Options are ⇒ (A) is R, (B) may be R and C, (C) is C, (D) is R and C in parallel, (E) , Leave your comments or Download question paper.

Question is ⇒ An RC impadence function has a pole at <i>s</i> = 0. The first element in the Foster form of synthesis, Options are ⇒ (A) is R, (B) may be R and C, (C) is C, (D) is R and C in parallel, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	An RC impadence function has a pole at s = 0. The first element in the Foster form of synthesis
A.	is R [Wrong Answer]
B.	may be R and C [Correct Answer]
C.	is C [Wrong Answer]
D.	is R and C in parallel [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ MF is generally used for
telegraphy
radio and television links
satellite communication
broadcasting, navigation

⇒ Tropospheric mode of propagation is used in
UHF
VLF
MF
HF

⇒ Octal number 12 is equal to decimal number
8
9
10
11

⇒ For a depletion type NMOS, V_p = - 4 volts. For V_GS = 0, 1_D = 16 mA in the pinch off region of V_DS. For V_GS = - 2, the value of I_D in the pinch off region of V_DS is given by
64 mA
32 mA
16 mA
4 mA

⇒

Assertion (A): In an intrinsic semiconductor J = (μ_n x μ_p)en_i.

Reason (R): Intrinsic charge concentration n_i at temperature T is given by n_i² = A₀ T³ e^-E_G0/kT.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ A 1000 kHz carrier is simultaneously modulated by 300 Hz and 2 kHz audio sine wave. Which of the following frequencies will not be present in the output?
998 kHz
999.7 kHz
1000.3 kHz
700 kHz

⇒ The resistivity of ferrites is
very much lower than that of the ferromagnetic metals
slightly lower than that of the ferromagnetic materials
slightly higher than that of the ferromagnetic metals
very much higher than that of the ferromagnetic metals

⇒ A vertical wire of 1 meter length carries a current of 1 A at 10 MHz. The total radiated power is nearly
0.13 W
0.88W
7.3 W
73 W

⇒ Which quantity controls the effectiveness of LED in emitting light?
Applied voltage
Current
Extent of doping
Temperature

⇒ In an R-L circuit, the impedance is 30 Ω at a frequency of 100 Hz. At 200 Hz, the impedance should be
30 Ω or more
60 Ω or more
15 Ω or less
more than 30 Ω but less than 60 Ω

⇒ The linear transistor circuits always operate in the
saturation
cut off
active
inactive

⇒ The gain of collinear arrays is maximum when the spacing between the elements is
0.1 λ to 0.3 λ
0.3 λ to 0.9 λ
0.5 λ to 0.7 λ
0.7 λ to 0.9 λ

⇒ Circuit shown in the figur
astable multivibrator
monostable multivibrator
VCO
ramp Generator

⇒ The ac collector current is nearly equal to
ac base current
ac signal current
ac supply current
ac emitter current

⇒ The problem associated with tuned-radio frequency receiver is
instability
insufficient adjacent frequency rejection
bandwidth variation
all of the above

⇒ Which is correct with respect to computer memory?
Only a particular address can have a particular memory
Any address can have any memory
To read a word from computer memory, it is not necessary to specify a location
None of the above

⇒ If absolute potential of A is - 8 V and that of B is - 16 V, V_AB is equal to
24 V
8 V
- 8 V
- 24 V

⇒ For high frequencies a capacitor like
an open circuit
a short circuit
either open circuit or short circuit
none of the above

⇒ In figure, Z₁ = 200∠60° Ω, Z₂ = 400∠ - 90° Ω, Z₃ = 300∠0°. Then Z₄ for bridge to be balanced
150∠30° Ω
400∠ - 90° Ω
300∠90° Ω
600∠ - 150° Ω

⇒ In an R-C series circuit excited by a voltage E, the charge across capacitor at t = 0⁺ is
0
CE
CE (1 - e^-t/RC)
none of the above

⇒ It is required to measure pressure using LVDT. The additional device needed is
strain gauge
pitot tube
bourden tube
rotameter

⇒ MTI stands for
Moving Target Indicator
Microprocessor Tracking Index
Multiplexed Telemetry Index
Maximum Transmission Index

⇒ Which of the following constitutes an active component?
Semiconductor device
Resistors
Capacitors
Inductors

⇒ The common-drain amplifier, better known as the source follower, has a voltage gain __________ and the output signal is __________ with the input signal.
approaching unity, in phase
approaching unity, out of phase
is very high, in phase
is very high, in reverse phase

⇒

Assertion (A): ∈₀ has the dimensions of farad per meter.

Reason (R): D = ∈₀∈_r E.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ A retriggerable one shot is one which
can be triggered only once
has two quasi stable states
can not be retriggered till the complete pulse appears at output
can be retriggered while the output is being generated

⇒ A nibble corresponds to
2 successive bits of data
4 successive bits of data
8 successive bits of data
16 successive bits of data

⇒

Assertion (A): A large negative feedback is deliberately introduced in an amplifier to make its gain independent of variation in parameters of active device.

Reason (R): A large negative value of feedback results in a high value of return difference compared to unity which makes the feedback gain inversely proportional to the feedback factor.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ In the BJT amplifier shown in the figure is the transistor is biased in the forward active region. Putting a capacitor across R_E
decrease the voltage gain and decrease the I/P impedance
increase the voltage gain and decrease the I/P Impedance
decrease the voltage gain and Increase the I/P impedance
none of the above

⇒ The amount of dielectric heating is inversely proportional to frequency.
TRUE
FALSE