Question is ⇒ The open loop gain of an amplifier is 200. If negative feedback with β = 0.2 is used, the closed loop gain will be, Options are ⇒ (A) 200, (B) 40.12, (C) 4.878, (D) 2.2, (E) , Leave your comments or Download question paper.

Question is ⇒ The open loop gain of an amplifier is 200. If negative feedback with β = 0.2 is used, the closed loop gain will be, Options are ⇒ (A) 200, (B) 40.12, (C) 4.878, (D) 2.2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The open loop gain of an amplifier is 200. If negative feedback with β = 0.2 is used, the closed loop gain will be
A.	200 [Wrong Answer]
B.	40.12 [Wrong Answer]
C.	4.878 [Correct Answer]
D.	2.2 [Wrong Answer]
View Answer 3 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the given figure shows a 4 bit serial in parallel out right shift register. The initial contents as shown are 0110. After 3 clock pulses the contents wil
0
101
1010
1111

⇒ Consider the following program for 8085 Adds decimal number 5 to contents of memory
Subtracts decimal number 5 from contents of memory
Subtracts decimal number 15 from contents of memory
Adds decimal number 15 to contents of memory

⇒ The unit of thermal resistance of a semi-conductor device is
Ohms
Ohms/°C
°C/ohm
°C/watt

⇒ One input terminal of high gain comparator circuit is connected to ground and a sinusoidal voltage is applied to the other input. The output of comparator will be
sinusoidal
full rectified sinusoidal
half rectified sinusoidal
square wave

⇒ A memory system of size 16 k bytes is to be designed using memory chips which have 12 address lines and 4 data lines each. The number of such chips required to design the memory system is
2
4
8
18

⇒ In a microstrip transmission the signal can be easily redirected by changing the centre strip.
TRUE
FALSE

⇒ It is required to trace the output characteristics of a CE bipolar transistor on a CRO screen. The proper method is
apply the voltage drop across collector resistance to Y input, disconnect sweep generator and apply V_CE to X input
apply voltage drop across collector resistance to Y input
apply V_CE to X input
apply V_CE to Y input, disconnect the sweep generator and apply voltage drop across collector resistance to X input

⇒ An ac bridge uses galvanometer as detector.
TRUE
FALSE

⇒ The charge per proton is
1.6 x 10^-19 C
2.6 x 10^-19 C
0.6 x 10^-19 C
1.6 x 10^-13 C

⇒ Which of the following transducers requires a high input impedance preamplifier for proper measurements?
Thermocouple
Piezoelectric
Thermistor
L.V.D.T

⇒ The tape recorders used in homes have
common head and common amplifier system for recording and playback
different heads and amplifiers for recording and playback
same head but different amplifiers for recording and playback
different heads but same amplifier for recording and playback

⇒ The drift velocity of electrons and holes is proportional to electric field strength.
TRUE
FALSE

⇒ The total area under the probability distribution curve is
1
0
depend upon curve equation
∞

⇒ For a quadratic factor in transfer function the phase angle is not a function of damping factor.
TRUE
FALSE

⇒ The mass of proton and electron are
1.672 x 10^-26 kg and 9.107 x 10^-31 kg respectively
9.107 x 10^-26 kg and 9.107 x 10^-31 kg respectively
9.107 x 10^-29 kg and 9.107 x 10^-31 kg respectively
9.107 x 10^-30 kg and 9.107 x 10^-31 kg respectively

⇒ RC oscillator can be used upto
1 kHz
10 kHz
50 kHz
100 kHz

⇒ If it is desired to have low output impedance in an amplifier circuit then we should use
common collector circuit
common base circuit
common emitter circuit
either (b) or (c)

⇒ x = AX + Bu is a state equation.
TRUE
FALSE

⇒ In a commercially available good power supply the voltage regulation is about
0.01
0.05
0.1
0.2

⇒ In a CB amplifier the maximum efficiency could be
0.99
0.85
0.5
0.25

⇒ Which one is true for writing array variable in Pascal?
The general form of an array variable is an integer or a real variable name followed by subscripts enclosed within square brackets. The subscripts are separated by commas
The general form of an array variable must be an integer name followed by subscripts enclosed within square brackets. The subscripts are separated by commas
The subscripts in array variable must be separated by dots
The subscripts must be enclosed within parenthesis

⇒ Consider a silicon p-n junction at room temperature having the following paramet
0.15 MV.com^-1, directed from p-region to n-region
0.15 MV.com^-1, directed from n-region to p-region
1.80 MV.com^-1, directed from p-region to n-region
1.80 MV.com^-1, directed from n-region to p-region

⇒ Typical value of power consumption of TV transmitter is
0.5 kVA
2 kVA
50 kVA
1000 kVA

⇒ In a digital counter the number of flip-flops is
always 2
always even
always odd
equal to the number of bits required in the final binary count

⇒ Dielectric constant, under the condition of alternating fields, is a complex quantity.
TRUE
FALSE

⇒ Which one is correct option?

A pure capacitor never dissipates energy, but only stores.
Capacitor can store finite amount of energy even cunent is zero.
The current through a capacitor is zero if voltage across it d.c.
Voltage across a capacitor cannot change instantaneously since it would require an infinite current.
q_c(0^-) = q_c(0⁺)

5, 4, 3, 2
3, 4, 1, 2
2, 4, 3, 1
1, 2, 3, 4, 5

⇒ The internal structure of PL A is similar to
RAM
ROM
both RAM and ROM
neither RAM nor ROM

⇒ A voltage v(t) which is a gaussian ergodic random process witha mean of zero and a varance of 4 volt² is measured by a meter which first square and then reads its dc component. The reading will be
0
4
16
2

⇒ In a single phase semi-converter the number of thyristors is
16
8
4
2

⇒ Which of the following can be used to convert PPM into PWM?
Integrator
Astable multivibrator
Bistable multivibrator
Monostable multivibrator