Question is ⇒ PROM is, Options are ⇒ (A) Permanent Read Only Memory, (B) Polarized Read Only Memory, (C) Positive Read Only Memory, (D) Programmable Read Only Memory, (E) , Leave your comments or Download question paper.

Question is ⇒ PROM is, Options are ⇒ (A) Permanent Read Only Memory, (B) Polarized Read Only Memory, (C) Positive Read Only Memory, (D) Programmable Read Only Memory, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	PROM is
A.	Permanent Read Only Memory [Wrong Answer]
B.	Polarized Read Only Memory [Wrong Answer]
C.	Positive Read Only Memory [Wrong Answer]
D.	Programmable Read Only Memory [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The capacitors C₁, C₃, C₄ and C₅ have a capacitance of 4 μF each and the capacitor C₂ has a capacitance of 10 μF. The effective capacitance (in μF) between the points X and Y will
4 μF
6 μF
3 μF
8 μF

⇒ In a magnetron the magnetic flux density is of the order of
1 mWb/s
1 Wb/m²
10⁶ m/s
10¹² m/s

⇒ Consider the following instruction of 8085 μp :

MOV M, A
AODC
MVI A, FF
CMP M

Which of these cause change in the status of flag(s)?
1 and 2
1, 2 and 3
3 and 4
2 and 4

⇒ The disadvantage of counter type ADC as compared to comparator ADC is that
resolution is low
conversion time is more
circuit is more complex
stability is low

⇒ The disturbance from adjacent power lines is known as
cross talk
cross fire
inductive disturbance
none of the above

⇒ The system with given pole-zero diagra
casual
non-casual
both sided
not-possible

⇒ An ideal rectifier should have
100% efficiency, zero ripple factor, zero harmonic factor and unity displacement factor
100% efficiency, zero tipple factor, zero harmonic factor and zero displacement factor
100% efficiency, zero ripple factor, unity harmonic factor and unity displacement factor
100% efficiency, unity ripple factor, zero harmonic factor and unity displacement factor

⇒ A buffer amplifier should have
high output impedance and high input impedance
high output impedance and low input impedance
low output impedance an low input impedance
low output impedance and high input impedance

⇒ Emitter follower is in which of following configuration.
common Base
common Emitter
common collector
common Base or common Emitter

⇒ A three state switch has three outputs. These are
low, low and high
low, high, high
low. floating, low
low, high, floating

⇒ If a line having Z₀ = 300 ∠ 0 W is short circuited at far end, VSWR is
0
1
∞
2

⇒ Regarding TASI which one of the following statements is wrong?
It snatches the channel in his speech and may allocate it to another speaker needing it.
The same speaker is reassigned a channel almost instantly when he speaks again even when the circuit is heavily loaded.
It increases the overall utilization of the transmission channel
Intercontinental callers sometimes confuse the effects of TASI with the effects of satellite delay.

⇒ The pole zero plot in the given figure is
non-minimum phase function
minimum phase function
all pass function
either (a) or (b)

⇒ 2's complement number 00011111 = __________ ₁₀
31
-31
11
-11

⇒ For real values of x, the minimum value of the function f(x) exp (x) + exp (- x) is
2
1
0.5
0

⇒ In a superheterodyne receiver with an IF of 450 kHz is tuned to a signal at 1200 kHz. The image frequency is
750 kHz
990 kHz
1650 kHz
2100 kHz

⇒ Consider a 300 Ω, quarter wave long at 1 GHz transmission line as shown in figure. It is connected to a 10 V, 50 Ω source at one end is left open circuited at the other end. The magnitude of the voltage at the open circuit end of the line
10 V
5 V
60 V
60/7 volt

⇒ In a conductor which of the following relations hold good?
∇ x D = r
∇ . D = r
∇ x D = 0
∇ . D = 0

⇒ In 8085, which of the following registers cannot be paired?
A
E
C
both (b) and (c)

⇒ Double spotting in a receiver is due to
poor sensitivity of RF amplifier
high gain of IF amplifier
inadequate image frequency rejection
all of the above

⇒

Assertion (A): ECL is fast as compared to TTL.

Reason (R): ECL dissipates less power than TTL.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒

Assertion (A): The forward dynamic resistance of p-n diode varies inversely with current.

Reason (R): The forward dynamic resistance of p-n diode varies with the operating voltage.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ For an ideal 3000 Hz channel, Nyquist rate is
3000 bps
6000 bps
9000 bps
12000 bps

⇒ At t = ∞; V_R2 and V_C wil
4, 4
2, 4
0, 2
2, 0

⇒ Which of the following characteristics is not true for TTL Logic?
Good speed
Low power dissipation per gate
High cost
None of these

⇒ The pole zero plot of the given figure is
non-minimum phase function
minimum phase function
all pass function
either (b) or (c)

⇒ In a shield helix
the spacing between adjacent turns is very large
the spacing between adjacent turns approaches zero
the spacing between adjacent turns approaches zero and wire thickness approaches zero
the spacing between adjacent turns is very large wire thickness approaches zero

⇒ Calculate the wave impedance for TM mode in rectangular waveguide for dominant mode at 3 GHz having
(120p) Ω
377 Ω
226 Ω
629 Ω

⇒ A 0 to 6 counter consist of 3 flip-flop and a combinational circuit of 2 input gates. The combinational circuit consist of
one AND gate
one OR gate
one AND and One OR
two AND gate

⇒

Assertion (A): Bolometer is frequently used in microwave power measurement.

Reason (R): In a bolometer the input microwave power causes a change in resistance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct