Question is ⇒ Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than, Options are ⇒ (A) 10 cm, (B) 15 cm, (C) 20 cm, (D) 30 cm, (E) , Leave your comments or Download question paper.

Question is ⇒ Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than, Options are ⇒ (A) 10 cm, (B) 15 cm, (C) 20 cm, (D) 30 cm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than
A.	10 cm [Correct Answer]
B.	15 cm [Wrong Answer]
C.	20 cm [Wrong Answer]
D.	30 cm [Wrong Answer]
View Answer 27 -5 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Castigliano's first theorem is applicable
for statically determinate structures only
when the system behaves elastically
only when principle of superposition is valid
none of the above

⇒ Which of the following is not the displacement method ?
Equilibrium method
Column analogy method
Moment distribution method
Kani's method

⇒ The fixed support in real beam becomes in the conjugate beam is
Fixed support
Hinged support
Roller support
Free support

⇒ Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is
2
3
6
8

⇒ A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear height between RCC slabs at top and bottom. The slenderness ratio of the wall is
15
19
20
25

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by
shear
vertical tensile splitting
buckling
any of the above

⇒ The force method in structural analysis always ensures
Equilibrium
Kinematically admissible t'orces
Equilibrium of forces
None of the above

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is
0.16 Wl
0.20 Wl
0.24 Wl
0.25 Wl

⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies
less than the left half span
whole of left half span
more than the left half span
whole span

⇒ The number of independent equations to be satisfied for static equilibrium in a space structure is
2
3
4
6

⇒ When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would
change from compression to tension
change from tension to compression
always be compression
always be tension

⇒ A free standing brick wall 20 cm thick is subjected to a wind pressure of 75kg/m2. The maximum height of wall from stability consideration is
0.64 m
0.96 m
1.28 m
1.5 m

⇒ A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be
8 kN.m
15 kN.m
30 kN.m
60 kN.m

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is
0.15 MPa
0.125 MPa
0.1 MPa
0.075 MPa

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ Direct load carrying capacity of a brick masonry wall standing freely as against when it supports RC slab will be
more
less
the same in both the cases
100%

⇒ The moment area theorems in the structural analysis fall in the category of
Force method
Displacement method
Stiffness method
Iterative method

⇒ Maxwell's reciprocal theorem in structural analysis can be applied in
All elastic structures
Plastic structures
Symmetrical structures only
Prismatic element structures only

⇒ In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as
sum of thickness of both leaves
two-third of the sum of thickness of both the leaves
actual thickness of the stronger leaf
larger of (b) and (c)

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ The principle of virtual work can be applied to elastic system by considering the virtual work of
internal forces only
external forces only
internal as well as external forces
none of the above

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ In the displacement method of structural analysis, the basic unknowns are
displacements
force
displacements and forces
none of the above

⇒ The three moment equation in structural analysis is basically a
Stiffness method
Displacement method
Energy method
Flexibility method

⇒ The three moments equation is applicable only when
the beam is prismatic
there is no settlement of supports
there is no discontinuity such as hinges within the span
the spans are equal

⇒ The method of moment distribution in structural analysis is
An iterative method
An exact method
An approximate method
None of these

⇒ Principle of superposition is applicable when
deflections are linear functions of applied forces
material obeys Hooke's law
the action of applied forces will be affected by small deformations of the structure
none of the above

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder
always occurs at center of span
always occurs under a wheel load
never occurs under a wheel load
none of the above

⇒ Unequal settlements in the supports of a statically indeterminate structure develop
Member forces
Reactions from supports
No reactions
Strains in some members only

⇒ For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is
0.211 L
0.25 L
0.234 L
0.5 L