Question is ⇒ The fixed support in a real beam becomes in the conjugate beam a, Options are ⇒ (A) roller support, (B) hinged support, (C) fixed support, (D) free end, (E) , Leave your comments or Download question paper.

Question is ⇒ The fixed support in a real beam becomes in the conjugate beam a, Options are ⇒ (A) roller support, (B) hinged support, (C) fixed support, (D) free end, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The fixed support in a real beam becomes in the conjugate beam a
A.	roller support [Wrong Answer]
B.	hinged support [Wrong Answer]
C.	fixed support [Wrong Answer]
D.	free end [Correct Answer]
View Answer 27 -3 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of
zero length
infinite length
zero moment of inertia
none of the above

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder
always occurs at center of span
always occurs under a wheel load
never occurs under a wheel load
none of the above

⇒ Water retentivity for brick masonry should not be less than
50%
60%
70%
80%

⇒ The torsional stiffness of a member can be defined as
Torque for unit moment
Torque for unit twist
Moment for unit twist
Torsion for unit twist

⇒ To generate the j th column of the flexibility matrix
a unit force is applied at coordinate j and the displacements are calculated at all coordinates
a unit displacement is applied at co-ordinate j and the forces are calculated at all coordinates
a unit force is applied at coordinate j and the forces are calculated at all coordinates
a unit displacement is applied at co-ordinate j and the displacements are calculated at all co-ordinates

⇒ The thickness of each leaf of a cavity wall shall not be less than
5 cm
7.5 cm
10 cm
15 cm

⇒ The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in
vertical direction
horizontal direction
inclined direction
the direction in which the deflection is required

⇒ The moment distribution method in structural analysis can be treated as
Force method
Displacement method
Flexibility method
None of these

⇒ The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to
R
R²
1/R
1/R²

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by
shear
vertical tensile splitting
buckling
any of the above

⇒ If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to
0 6
0.75
0.85
0.95

⇒ Independent displacement components at each joint of a rigid-jointed plane frame are
three linear movements
two linear movements and one rotation
one linear movement and two rotations
three rotations

⇒ The three moment equation in structural analysis is basically a
Stiffness method
Displacement method
Energy method
Flexibility method

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ In moment distribution method, the sum of distribution factors of all the members meeting at any joint is always
zero
less than 1
1
greater than 1

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of
1.2
1.4
1.6
2.0

⇒ Select the correct statement
Flexibility matrix is a square symmetrical matrix
Stiffness matrix is a square symmetrical matrix
both (a) and (b)
none of the above

⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is
unstable
stable and statically determinate
stable and statically indeterminate
none of the above

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust
is increased
is decreased
remains unchanged
becomes zero

⇒ Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is
2
3
6
8

⇒ A free standing brick wall 20 cm thick is subjected to a wind pressure of 75kg/m2. The maximum height of wall from stability consideration is
0.64 m
0.96 m
1.28 m
1.5 m

⇒ The deformation of a spring produced by a unit load is called
stiffness
flexibility
influence coefficient
unit strain

⇒ Which of the following methods of structural analysis is a force method ?
slope deflection method
column analogy method
moment distribution method
none of the above

⇒ The fixed support in real beam becomes in the conjugate beam is
Fixed support
Hinged support
Roller support
Free support

⇒ In plastic analysis the shape factor for a circular section is
1.5
1.6
1.7
1.75

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of
0.4 kg/cm2
0.7 kg/cm2
1.0 kg/cm2
1.2 kg/cm2

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is
0.16 Wl
0.20 Wl
0.24 Wl
0.25 Wl

⇒ A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
5 mm
0.5 mm
0.05 mm
0.005mm

⇒ The analysis of statically indeterminate structures by the unit load method is based on
Consistent deformation
Stiffness method
Consistent force
None of these

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by
2j - r
j - 2r
3j - r
2j + r