Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to |

A. | 0 6 [Wrong Answer] |

B. | 0.75 [Wrong Answer] |

C. | 0.85 [Correct Answer] |

D. | 0.95 [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is

0.15 MPa

0.125 MPa

0.1 MPa

0.075 MPa

⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies

less than the left half span

whole of left half span

more than the left half span

whole span

⇒ The width of the analogous column in the method of column analogy is

2/EI

1/EI

1/2 EI

1/4 EI

⇒ In moment distribution method the sum of distribution factors of all the members meeting at any joint is always

Zero

< 1

> 1

= 1

⇒ The fixed support in a real beam becomes in the conjugate beam a

roller support

hinged support

fixed support

free end

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ The deformation of a spring produced by a unit load is called

stiffness

flexibility

influence coefficient

unit strain

⇒ The method of moment distribution in structural analysis is

An iterative method

An exact method

An approximate method

None of these

⇒ The Castigliano's second theorem can be used to compute deflections

in statically determinate structures only

for any type of structure

at the point under the load only

for beams and frames only

⇒ For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is

0.211 L

0.25 L

0.234 L

0.5 L

⇒ In the displacement method of structural analysis, the basic unknowns are

displacements

force

displacements and forces

none of the above

⇒ For strengthening a 50 m long and 5 m high straight compound wall built in brick work, which one of the following would be most suitable?

providing buttresses at certain intervals

providing a deeper foundation

using a richer mortar

using stronger bricks

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of

1.2

1.4

1.6

2.0

⇒ A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be

8 kN.m

15 kN.m

30 kN.m

60 kN.m

⇒ Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have

high shrinkage

less strength

both (a) and (b)

none of above

⇒ The timber floor not spanning on the masonry wall but properly anchored to the wall gives

lateral restraint but not rotational restraint

rotational restraint but not lateral restraint

both lateral and rotational restraints

neither lateral nor rotational restraint

⇒ If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is

unstable

stable and statically determinate

stable and statically indeterminate

none of the above

⇒ The principle of virtual work can be applied to elastic system by considering the virtual work of

internal forces only

external forces only

internal as well as external forces

none of the above

⇒ A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear height between RCC slabs at top and bottom. The slenderness ratio of the wall is

15

19

20

25

⇒ Water retentivity for brick masonry should not be less than

50%

60%

70%

80%

⇒ If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to

0 6

0.75

0.85

0.95

⇒ The number of independent equations to be satisfied for static equilibrium of a plane structure is

1

2

3

6

⇒ Select the correct statement

Flexibility matrix is a square symmetrical matrix

Stiffness matrix is a square symmetrical matrix

both (a) and (b)

none of the above

⇒ For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than

Vt x height of shorter opening

Vt x height of longer opening

Ax height of shorter opening

Vi x height of longer opening

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of

0.4 kg/cm2

0.7 kg/cm2

1.0 kg/cm2

1.2 kg/cm2

⇒ The truss can be analysed by the methods of joints when the number of unknown at a joint is equal to

1

2

3

4

⇒ Unequal settlements in the supports of a statically indeterminate structure develop

Member forces

Reactions from supports

No reactions

Strains in some members only

⇒ If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by

m + r + 2j

m - r + 2j

m + r - 2j

m + r - 3j

⇒ Degree of kinematic indeterminacy of a pin-jointed plane frame is given by

2j - r

j - 2r

3j - r

2j + r