Question is ⇒ In CCIR-B system, the time between start of one H syn. pulse and next is, Options are ⇒ (A) 64 μs, (B) 6.4 μs, (C) 640 μs, (D) 0.64 μs, (E) , Leave your comments or Download question paper.

Question is ⇒ In CCIR-B system, the time between start of one H syn. pulse and next is, Options are ⇒ (A) 64 μs, (B) 6.4 μs, (C) 640 μs, (D) 0.64 μs, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In CCIR-B system, the time between start of one H syn. pulse and next is
A.	64 μs [Correct Answer]
B.	6.4 μs [Wrong Answer]
C.	640 μs [Wrong Answer]
D.	0.64 μs [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In figure the output v(t)
an amplitude modulated signal
a frequency modulated signal
a phase modulated signal
none of the above

⇒ The v-i characteristics of a diode may be linear or non linear.
TRUE
FALSE

⇒ The self inductances of two coils are 27 H and 3 H. If the winding or coils is such that 50% of flux of one links the other, the mutual inductance is
30 H
24 H
9 H
4.5 H

⇒ The four types of integers in Java are called
byte, short, int and long
bit, byte, short and long
nibble, byte, short and long
nibble, byte, int and long

⇒ Satellite communication systems use the frequency band
10 to 20 MHz
50 to 70 MHz
3 to 6 GHz
100 to 120 GHz

⇒ 23.6₁₀ = __________ ₂
11111.1001
10111.1001
111.101
10111.1

⇒ Top loading in an antenna increases
effective height
beam width
input capacitance
bandwidth

⇒ The v-i characteristics of a FET is shown in figure. In which region is the device biased for small signal amplifica
AB
BC
CD
BD

⇒ When an SCR is in forward blocking mode, the applied voltage
appears across only one junction
is equally shared by two junctions
is equally shared by three junctions
may appear across one or more junctions

⇒ Half bridge and full bridge inverters of one type use different commutation methods.
TRUE
FALSE

⇒

Assertion (A): Impatt diode can be used in both amplifiers and oscillators.

Reason (R): Impatt diode has a low resistance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ MTI stands for
Moving Target Indicator
Microprocessor Tracking Index
Multiplexed Telemetry Index
Maximum Transmission Index

⇒ In D-type FF, Preset (Pr) and clear (Clr) inputs are called
Synchronous
Asynchronous
Data
None

⇒ In a digital measuring device the input electrical signal is in the frequency range of dc to ac (50) Hz. It must be sampled at a rate of
f times/sec
0.5 f times/sec
0.25 f times/sec
2 f times/sec

⇒ Consider the following logical IF statement in FORTRAN 77 IF (SALT - PEPPER) 11, 11, 13
IF (SALT - PEPPER) 13, 11, 13
IF (SALT - PEPPER) 13, 11, 11
IF (SALT - PEPPER) 11, 13, 13

⇒ A ramp input applied to a unity feedback system results in 5% steady state error. The type number and zero frequency gain of the system are respectively.
1 and 20
0 and 20
0 and 1/20
1 and 1/20

⇒ In 8085 microprocessor, in order to enable INTR interrupt, which of the following instruction are needed?
EI only
SIM only
El and SIM both
None

⇒ The emf of a Weston cell is 1.286 V.
TRUE
FALSE

⇒ In 8085 eight address and data buses are multiplexed.
TRUE
FALSE

⇒ Integral error compensation changes a second order system to
first order system
third order system
fourth order system
either (a) or (b) depending on the system

⇒ The inputs to a 4 channel MUX have the following bandwidths. Channel 1-50 Hz, channel 2-200 Hz. Channel 3-75 Hz. Channel 4-90 Hz. The theoretical minimum sampling rate of the MUX is
200 Hz
400 Hz
415 Hz
1600 Hz

⇒ Which of the following has the highest input impedance?
CE
CB
CC
Push pull

⇒ If the valence electron is separated from a copper atom, the remaining part of atom has a net charge of
1
-1
0
3

⇒ The selectivity curve of a standard receiver is represente
curve A
curve B
curve C
curve D

⇒ In 8085 the instruction MOV A, M is an example of
Direct addressing
Immediate addressing
Register addressing
Register indirect addressing

⇒ For operation of enhancement only N-channel MOSFET, value of gate voltage has to be
zero
low positive
high negative
high positive

⇒ In a pure capacitive circuit if the supply frequency is reduced to 1/2, the current will
be reduced by half
be doubled
be four times as high
be reduced to one fourth

⇒ An RLC series circuit
resonant frequency is high
Q is high
bandwidth is large
Q is low

⇒ The self bias provides
stable Q point
large voltage gain
high input impedance
high base current

⇒ At absolute zero temperature a semiconductor behaves like
an insulator
a super conductor
a good conductor
a variable resistor